“Greenie” GLF550/650/650ER – Part 1

Introduction

In case you are lost… Greenie is one of the nicknames of this famous business jet aircraft manufacturer. On behalf of X-Plained.Com, Angelique, your long-time personal reporter, has finally decided to review the GLF550/650 models from AKD Studio, the only X-Plane developer modelling this manufactured business jet. I contacted AKD Studio directly, and via simMarket, I got the aircraft models from Antoni. And here we are … starting with Part 1 of the GLF550/650 review. I write on purpose, Part 1, which means there will also be a Part 2. Part 1 will most likely already be a long, informative review. When I add a complex flight review to this, it will be too long; that said, the test flight will be included in Part 2 with lots of other tips and tricks.

The first Grumman Gulfstream I
A huge difference with todays Gulfstream aircraft

Part 1 of this review covers both GLF550/650 models, including the exterior and interior expectations, operational procedures, and additional steps. Part 2 will be dedicated to a comprehensive test flight, in which I will break down the overall flight into its respective flight phases. Besides that, I will add sections on what we call nice and what we need to know.

As of today, June/July 2026, AKD Studio offers the GLF550, its first model. It is modelled for both X-Plane 11 and X-Plane 12. Later, the GLF650 /650ER was added. Hold on, what are those differences then? Ok, let me highlight this in detail for you.

The GLF550 has a maximum range of 6750 NM with a cruising speed of M0.80. The GLF650 offers a slightly longer range, namely 7000 NM, with a cruising speed of M0.85. But the design differences are much more interesting. While the GLF550 has a traditional flight control system, the GLF650 has a Fly-by-Wire System. Although both cabins are of the same luxury standard, the GLF650 has more advanced features and a more spacious cabin layout, and it is still in production, while the GLF550 isn’t.

A quick look suggests that the GLF650 offers a longer range, higher cruising speed, and more advanced technology than the GLF550. These differences make the GLF650 a more capable aircraft for long-distance travel and modern aviation needs.

Typical drawing of the Gulfstream G650. Courtesy flightglobal.com

X-Plane 12 developers offer several small business jets like the X-Crafts Embraer ERJ Lineage 600 and the Embraer E-Jets 1000, the Take Command! Hot Start Bombardier Challenger 650, Aerobask Embraer Phenom 300, VSkyLabs Citation 510X, X-Hangar Learjet 35A. Aerobask is also developing the Dassault Falcon 8X, but it’s still in development, so it’s not available yet. There is another Gulfstream model on the market from X-Hangar, but since I don’t own that one, I can’t say much about it; this is the only competitor. Period!

One general rule for all models is:
– How well are the 3D aircraft modelled, and what is their level of detail?
– How well does the virtual cabin look, in particular, for business cabins?
– How realistic do the flight deck textures look?
– How “deep” are the aircraft, navigation, communication and Auto Flight systems modelled?

For Part 1, it is important to me to check whether improvements are needed or if it is already of high quality. You often hear that the aircraft are “eye-candy” modelled, but the systems’ reality lacks or sometimes the other way around. With my technical background as a ground engineer, I find it important that systems are modelled realistically, as far as possible within X-Plane 12, but, honestly, the look is also important.

AKD Studio
Antoni Rybka, the lead and sole developer of the GLF550/650 aircraft, has created an aircraft that is not the easiest to model. In particular, the real 650 may look beautiful and famous among many rich people; it is also a sophisticated and complex aircraft, especially the GHLF650/650ER, due to its Fly-by-Wire system. Taking that into account, it is not easy to model this in detail. Up to me to see how these models look, how the systems are modelled, and in Part 2, how it flies.

Curious as I am, I wanted to know if he does all the work himself or if AKD Studio has other members. According to AKD Studio, “As for the development work: yes, I do everything myself, including the 3D modelling, texturing, and systems programming. The project is finished in terms of release, but I am still actively improving it. I am also working on improving the textures and the 3D model. At the moment, I am not yet able to show any progress, as I have only just started working on these improvements. However, once I have something ready to show, it will definitely appear on my social media channels.”

Antoni doesn’t have his own website, but he uses several other social platforms like YouTube, Facebook, Instagram, Discord Channel, and, formerly known as Twitter, but an X account has been created, and no posts have been posted as of June 2026. Looking at these platforms, I think the most important communication platforms for AKD Studio are his Discord Channel, the X-Plane.Org forum, and his YouTube Channel, that offers many tutorials.

Last but not least, for those who want to know a bit more about these aircraft models, it is worth checking out the Code450.com website. (https://www.code450.com/) This website covers everything related to Gulfstream aircraft, from the G450 to the G800. Or as they say themselves, “Code450 is a website made by Gulfstream pilots for Gulfstream pilots. We are all here to learn and to share information about the G450, G550, G500, G600, G650, and G700/G800.”

The real Gulfstream 550, 650 and 650ER

The following information is taken from both the Gulfstream website and Wikipedia, with assistance from AI.

“Gulfstream was born from an original idea: to develop the world’s first aircraft designed for business travel. The first flight of the Gulfstream I in 1958 marked the start of the business aviation era. In the decades since, we have forged a legacy of safety, technical expertise, performance and comfort defined by the exceptional aircraft we build.”

“Gulfstream is a business jet manufacturer and a visionary leader in the aviation industry. We design, build and service next-generation aircraft that accelerate the pace of global commerce. Gulfstream jets save valuable time, strengthen connections around the world and enable specialised missions for scientific research and humanitarian purposes. Gulfstream Aerospace Corporation is an American aircraft company and a subsidiary of General Dynamics. Gulfstream designs, develops, manufactures, markets, and services business jet aircraft.”

“Gulfstream has been proud to call Savannah, Georgia, home since 1967. Our expansive Savannah campus encompasses our worldwide headquarters, an advanced Research and Development Campus, a design showroom, state-of-the-art precision manufacturing and completion facilities, and a newly expanded Customer Support service centre.”

Installation, Add-Ons and Updates

Installation
As said before, I got my AKD Studio GLF models from simMarket. Thanks, Antoni, for this speedy service. Each model has its own ZIP file, and I also received the serial code separately to unlock the GLF550/650. Nothing special about this. Once each model has been unzipped, you can either copy and paste them into the X-Plane Aircraft folder or create your own AKD Studio folder and place those packages into it. Then you start up X-Plane 12, load one of the GLF model(s) you bought, and enter the serial upon loading the aircraft. Reload the model with Art, and you’re done, although it is in most cases better to shut down X-Plane and restart/reload either GLF aircraft. Worth highlighting that each GLF model has its own serial key.

Add-On: Skunkcrafts updater
Next, you need to keep your model up to date using the Skunkcrafts updater. You could also re-download the model from simMarket or X-Plane.Org, but it is easier and quicker to use the Skunkcrafts updater. The Skunkcrafts plugin can be downloaded from this dedicated link. A quick note about the Skunkcrafts plugin: you also have a Standalone Client package. The standalone client allows you to update the supported product without the need to start X-Plane.

Add-On: AviTab
The AKD Studio GLF models are fully integrated with AviTab (Aviation Tablet). When I write “fully”, I mean not only the AviTab device with its basic functions, but also SimBrief integration, TO and LDG data tabs, the Weight and Balance tab, and a direct, bidirectional link to the GLF550/650 tablet or EFB (Electronic Flight Bag). You can grab your copy via this X-Plane.Org link or directly via the AviTab GitHub page. The current AviTab version as of June 16th 2026, is 1.1.0.

As you might know, the AviTab EFB plugin is something different from the AKD Studio EFB. Ok, they use the same name … “EFB”, but the AKD Studio EFB is available by default and, unfortunately, not yet as a pop-up. Hopefully, a pop-up version will appear later with updates.

Wrapping it up, the AKD Studio EFB is positioned on each side window. Very convenient for you as a virtual pilot, especially when using VR. As briefly mentioned earlier, the AKD Studio EFB can link your SimBrief/Navigraph account to the tablet. This allows you to download flight plans, for example, directly into the FMS MCDU. And the AviTab lets you store charts and other documents in its designated folder. It will then be all available via the AviTab for your cockpit preparations.

Add-On: SmartCopilot
In the GLF550/650 folders, you find the smartcopilot.cfg file. Smartcopilot from Sky4Crew makes it possible for two virtual pilots to share the same cockpit, so you can fly and interact as captain and copilot. I am wondering if Smartcopilot is still alive, as they say. A while ago, I had a chat with Max from Copilot, who informed me that he no longer supports this software.

However, I must admit that the old website and the new one still exist. However, on the old website, Smartcopilot version 3.3.x dates back to 2021. The new website covers Smartcopilot version 4, a trial version of the plugin, and lets you test existing aircraft configurations and connection stability; however, pricing plans are still TBD (To Be Determined).

I have read at several places that the old Smartcopilot 3.3.x, which was originally only for X-Plane 11, also works with X-Plane 12. Time for me to contact AKD Studio and ask Antoni why he chose Smartcopilot rather than, for example, SharedFlight? According to AKD Studio, “I added it because some customers with a SmartCopilot subscription were asking for it. Please note that the aircraft configuration currently works only with SmartCopilot v3. I may also add SharedFlight support in the future.”

Long story short, the GLF550/650 packages already have the smartcopilot.cfg file, which means that when you own SmartCopilot 3.x, you can connect straight away with your companion virtual pilot. Finally, I tried to find other freeware “shared cockpit” software and found a couple; however, they are all from a while back and haven’t been updated.

Add-On: SimBrief AKD Studio Profiler
Assuming you’re a virtual simmer using SimBrief for your flights, these AKD Studio created SimBrief Profiler files are an absolute necessity. These profiler files contain the correct performance data of the GLF550/650. Without these files, SimBrief has no dedicated file for the AKD Studio GLF aircraft.

You can download these SimBrief files for the GLF550 from this link, for the GLF650 you use this link and finally, for the GLF650ER this URL. Click the corresponding link to open the SimBrief GLF performance page.

An example of the GLF550 SimBrief Profiler file

Add-On: AIRAC Cycles
And last but not least, you need up-to-date AIRAC cycles for your navigation. Let me explain this in detail for those new to X-Plane. AIRAC (Aeronautical Information Regulation and Control) cycles are aeronautical information which is constantly changing: airspace structures and routes are revised, navigation aids change, SIDs (Standard Instrument Departure) and STARs (Standard Terminal Arrival Route) are amended, and runway and taxiway information change.

Navigraph is the go-to source for everything you need for flight simulation. You must opt in for a Navigraph account. Once that’s done, you can select an Ultimate package on a monthly or yearly basis. You save 25% with the annual account compared to the monthly subscription.

Since SimBrief is an integral part of Navigraph, you can log in with the same credentials as your Navigraph subscription. But if you want to consider a Navigraph subscription, you can use SimBrief separately for free. The only thing you need to do is create a SimBrief account on the Navigraph website. More about the SimBrief integration later in this review.

Updates
I highlighted this already; the Skunkcrafts updater keeps the GLF550 and GLF650 aircraft up to date. In the GLF550/650 aircraft folder, you will find the skunkcrafts_updater.cfg file but no skunkcrafts_updater_beta.cfg file, which you sometimes see with other developers. Since I missed the skunkcrafts_updater_beta.cfg file and informed AKD Studio why it isn’t there. According to Antoni, “Yes, that’s correct – there is no separate .cfg file dedicated to beta updates at the moment. Setting up beta updates through SkunkCrafts requires additional server-side configuration, and I simply haven’t done that yet. I’ll add it at some point in the future.”

Documentation and Liveries

Documentation
Each model – GLF550 and GLF650 – has a documentation folder that can be found in the aircraft folder. This folder offers the following Adobe Acrobat documents:

– GLF550/650 by AKD Studio Introduction (7 pages)
– GLF550/650 by AKD Studio – MCDU Manual (57 pages)
– GLF550/650_AKD_Checklist (2 pages)
– Support text file (speaks for itself 1 page)

The GLF550/650 by AKD Studio Introduction manual discusses, in addition to installation, activation, and adding liveries, the AKD Studio EFB. It briefly explains what each EFB page/window does. I will highlight the AKD Studio EFB in more detail later. But this manual won’t explain the simulated systems or how to control the different pages on the PFD and ND DUs. On the other hand, AKD Studio offers a full tutorial that covers all the systems, how to start them up, how to start your engines, and how to complete a full flight. Still, I found it useful when AKD Studio could provide, in the near future, a manual that specifically covers the DUs and how to control them, and not to forget the HUD (Head Up Display).

I would like to add one thing, since this is not clearly explained: the use of AC or DC external power. Most simmers know what the AC EXT PWR does: an external AC power source may be connected to the aircraft for ground servicing and/or maintenance. The DC EXT PWR receptacle is more commonly found on smaller jets. The DC external power supply is for APU start-up or to power the ground service bus for servicing, maintenance, or preflight inspections. Although this information is for the G450 aircraft model, it also applies to newer models. (Courtesy of www.code450.com)

The GLF550/650 by AKD Studio – MCDU (Multifunction Control Display Unit) manual covers everything related to the MCDU in a logical order. It is not a static manual on what each button or display does; no, it is an active guide based on a typical flight. Wherever needed, additional information is given about the necessary steps to take. The flight departs from EPWA; arrival at EPKK. The departure discussed is from runway 29 and uses EVINA7G as the SID (Standard Instrument Departure). The arrival at EPKK goes via STAR (Standard Terminal Arrival Route) KUKAM4G with an ILS landing on runway 25. Sometimes “they” say that STAR stands for Standard Instrument Arrival. Both are valid names.

Keep in mind that certain pages, including their MCDU images, may differ from the current AIRAC cycle. According to the AKD Studio MCDU manual, the active AIRAC cycle was in effect as of October 2024, while we are currently in July 2026. Not an issue, but it is possible that, for example, the SID or STAR has been changed or the SID/STAR number has been updated.

Wrapping it up, the manual starts by showing how to enter the flight plan route manually, then how to load it from simBrief and your saved flight plan from the X-Plane Output/FMS plans folder. When either of these flight plan steps is completed and reviewed, and you have scrolled through the flight plan, continue with the performance pages, including the takeoff initialisation and VSpeeds. Overall, I can’t say anything other than that it’s an extensive, well-written, full-of-detail manual with lots of examples related to the sample flight.

And finally, the GLF550/650_AKD_Checklist. This is the Standard Normal Procedures list, without any explanation.

I mentioned it before, but it’s worth saying again: for complete tutorial flights, I urge you to check out the AKD Studio dedicated YouTube channel. Each flight tutorial (GLF550/650) takes around 30-33 minutes, so not too long, and the flights cover the same flight as the MCDU manual, which I discussed before.

Liveries
The GLF550/650 package comes with a couple of liveries, but when you are not satisfied, then check out the GLF550 livery link and the GLF650 livery link.

These links not only offer liveries, but also paint kits and addons.

X-Plane menu Settings and More

X-Plane AKD Studio Menu
The X-Plane GLF550/650_AKD XP12 menu consists of “Show/Hide Captain/Copilot Tablet, “Instant IRS alignment” and “Show/Hide different Popup Panels”. The show/hide tablet option is simple: the tablet, read EFB, is there, or it is not. Then the IRS alignment. Normally, the IRS (Inertial Reference System) takes many minutes to fully align, but you can set it to align instantly, which is, of course, less realistic. Up to you!

The show/hide of the DUs (Display Units), the MCDUs, and the Display Controller, only applicable for the GLF550, opens as a separate X-Plane window. It allows you to move it to another monitor or, for Apple users, to your iPad, or, if you have the Mac mini or Mac Studio and more than one monitor, to another monitor. Then the GLF650 has an additional function, namely “Stow RAM AIR TURBINE (RAT)” in case it was extended during flight.

AKD Studio tablet
The AKD Studio tablet or EFB (Electronic Flight Bag) is their own design with their own pages or tabs, whatever you call them. The AviTab plugin can be part of it, but without it, it just works as well. The AKD Studio EFB has no option to move the tablet, but it does have an ON/OFF button on the left-hand side in the middle. As mentioned before, you can’t disconnect it from the window and use it as a separate floating unit.

The EFB display can be dimmed via the Settings icon, EFB BRIGHTNESS and with your mouse wheel, you can dim the EFB DU.

The EFB offers the following tabs:
– Fuel Payload
– GND
– AviTab
– Flight Plan
– PERF(ormance) calculator
– Settings
– Checklists
– Audio volume
– Cabin Lights
– Cabin PA
– Load/Save

Most of these pages are self-explanatory, but for some of them, I would like to go a bit deeper.

Although the Fuel Payload page speaks for itself, it allows you to download the necessary data directly from SimBrief via the INSERT SIMBRIEF DATA button, provided you created your flight plan there. Double-check that, via the EFB Settings page, you have selected either Kilograms or Pounds.

The GND page consists of two pages. Although not complicated, you can select individual ground objects ON on the so-called Static Elements page.

The Flight Plan page lets you load your saved flight plan directly from SimBrief. It may be obvious that the saved SimBrief flight plan page must be configured with the correct aircraft type; during loading, it will say that you created a flight plan using the wrong aircraft.

The PERF calculator page starts with the TAKEOFF performance page, while the lower right-hand button opens the LANDING performance page. After you retrieve the data from the sim, you can transfer the takeoff speed to the FMS via the SEND DATA TO FMS button. The “flow” works the same for the landing performance page.

Checklist
As mentioned earlier, there’s a paper version of the checklist in the Documentation folder. Then you will find at the AKD Studio EFB tab Checklist all the steps to perform, but these pages are not interactive.

My preference is an interactive checklist; thus, when you switch a system ON or set a knob to the correct position, it provides feedback that you have done so. And that brings me to the XChecklist plugin with user-created clist text files.

XChecklist with clist
Although this paragraph isn’t related to the AKD Studio checklist tab, I would like to bring it to your attention.
If you prefer the famous XChecklist plugin with a dedicated written clist text file, I have good news. I found two clist text files for the GLF models. First, a clist file from X-Plane.Org user xplanepeter1955 for the GLF650/650ER. Then there is a clist from Org user SkyBloo for the GLF550 that can be downloaded from this URL.

On a personal note, the clist from xplanepeter1955 covers a lot, so it is my personal preference, but it was only made for the GLF650/650ER. I guess it can also be used with the GLF550, but with some restrictions.

The last icon is the Load/Save. What is the use of this, and how handy can it be? Suppose you’re busy with all your preparations, have followed the built-in checklist, or use the clist XChecklist, and have finished a section. Let’s assume you finished loading the FMS MCDU. When you click the Load/Save icon, you can enter a “state file name”, for example, finished_MCDU_programming. I haven’t found out how many characters you can use, but it’s at least 32.

I tried to enter more, which was possible; however, it goes beyond the text box. Anyway, you click the SAVE STATE TO FILE dark grey button. You won’t see it immediately in the box next to it, but when you click the RELOAD FILES LIST, it will appear right here. And so you can create many state files like READY FOR PUSHBACK, READY FOR ENGINE START, and so on.

What is then the advantage of all of this? When you save these state files, you are actually saving the aircraft’s current state/condition. You can reload them at another moment and continue with your preparation, or even when you are already in flight. When I start Part 2, I will frequently refer to them and explain why I saved that particular situation. And where can you find these saved situation files? Go to the GLF550/650/650ER OUTPUT/panelstates folder. Here you will find all the saved files.

External Inspection

After all of the needed basic stuff, it is time to do my walk-around check or my technical inspection, whatever you prefer. Antonio from AKD Studio told me already that “I am also working on improving the textures and the 3D model.” Good, let’s start at the Nose Landing Gear (NLG), but first, the overview.

From a distance, the model looks well done. I haven’t checked the 3D-modelled fuselage against a real drawing, nor have I checked the wing model against the real wing, and so on. But what I said, I like the 3D GLF models. It even looks to me, from a distance, that the nose landing gear is modelled with an eye for detail. As curious as I am, let’s check that out.

Note: the aircraft base files, such as Fuselage_ALB, Fuselage_main_2_ALB, Fuselage_main_3_ALB, Landing_Gear_ALB, and Wings_ALB, located in the objects folder, are all 4K, and each has its own NRM (Normal Map image file that defines how light interacts with a surface’s texture, creating the illusion of depth and reflectivity) file. Other files are either 4K, some 2K, and I have even seen 1K, but the majority is 4K, which is good news, although 8K is also possible with X-Plane 12.

Walking to the NLG, it looks to me like this gear and wheel are modelled with lots of detail; however, they all look a bit the same colour. It is either light grey or almost white, and since all parts are white, it is difficult to distinguish the individual parts. The light bulbs on the NLG are beautiful; let’s be honest about that. They simulate LED bulbs. Well done. On the front nose, you can clearly see the pitot probes, but they are closed. You don’t see an opening, and they are almost blindly attached to the skin. And this brings me to the first item for improvement. All the components attached to the fuselage, wing, or tail skin are blind-mounted, though they are most certainly mounted with rivets, so you should see them too.

With the passenger door extended, you have a beautiful view of the entrance stair with handrails. And yes, you might think it looks simple. But it is very well modelled. It is a sleek stair; the cables, as in real life, are not visible; the stair linkage is well modelled, including the chrome-finished handrail. Well done.

And the other thing I noticed is that the fuselage skin looks like an eggshell. You don’t see any Aluminium skin liners, no rivets, nothing, and even the Aluminum skin is 100% flush. This is also applicable to the wing, leading edge in particular, and the tail of the fuselage. I can imagine that real aircraft are as smooth as possible. It is a high-end business jet, flying at high speeds and for long durations; to achieve this, the aircraft must be as smooth as possible. But not like it is modelled, so this is probably one of those 3D model and texture improvements Antoni was talking about.

I just mentioned the pitot probes. On the left-hand side of the fuselage, beneath the pitot probe, I see some quick fasteners; however, I don’t see a panel for that. On the to-do-list!

Normally, you would expect the NRM files to create a 3D illusion, but that doesn’t seem to be working well. Another good example is the skin around the cabin windows. I definitely think it will be as smooth as possible, but in one way or another, you should see rivets or a slight depth difference between the window pane and the Alu skin, creating a kind of 3D illusion. I move along the fuselage skin to the wing leading edge. Just before the fuselage/wing fairing, I see two holes with a shiny ring around them that sticks out. No idea what it could be, for sure not the static ports, but it feels a bit weird for a fuselage skin that should be as smooth as possible.

The wing leading edge, but also the top/bottom skins, are of the same type as the fuselage, the eggshell look. This looks nice; however, it is not the reality. Hopefully, Antoni will improve this to a more realistic look, which means you will definitely see the Alu skin sections and rivets in one way or another. Since the wing is made of Aluminium and thus has ribs and longerons, you should see this on the top/bottom skin of the wing when you look over it.

And hopefully, another modification can be implemented: the landing light unit at the wing leading edge. It has, in my humble opinion, a little fewer polygons. A bit more polygons and thus a rounder look would be a good idea. The winglet looks very nice, but here, too, no rivets or skin differences, even when it is mounted with rivets or bolts on one side or the other to the wing structure. It is now too smooth.

From a distance, the wingtip navigation/strobe unit looks good, but when you zoom in, I feel some realism is missing, and I am also not sure if it is modelled as how the real unit looks, but I have to be honest, I haven’t found any real close-up photo of this. Via the wing trailing edge, I spot several static dischargers- good news- but a small note for these static dischargers: they are blind-mounted, while I know for sure that rivets are used and thus rivets should be visible.

And then the Main Landing Gear (MLG) project.
It is done with great precision, but it misses something. As far as I can see, all the components of the landing gear have the same light grey/white colour. You can see the different components, but they almost blind into each other, so this is a texture issue. The main wheel rims have almost no detail, whereas the NLG wheels show a bit more detail. A bit of weathering would be welcome.

Note: this is particularly with the GLF550 model.
The GLF650 has a much more detailed wheel assembly. It could be that a cover is placed over the main wheel rim, but this is difficult to see/to judge. I feel that the MLGs need some revision too in 3D construction and textures. While here, an easy-to-modify MLG door is available with new textures and updated NRM files. Either the door is made of a single large honeycomb plate, or it is an Aluminium construction. When the latter is the case, you should see the skin plates mounted together to the ribs with rivets. Now it is one smooth plate.

One step further, I reach the engine cowling, the nose inlet, the fan section, and the tailpipe. Although Antoni did a good job, some improvements are in my humble opinion welcome. The overall engine cowling is too smooth (that eggshell look), but the leading edge of the engine inlet is riveted to the rest, as it is in 99% of the cases. Now you don’t see that at all. If the fan blades look and feel OK, I have no idea. I don’t see any panels with quick fasteners, such as an oil-filling panel, and no decals that should be positioned next to this panel or others. The reverser bucket doors are too clean on the inside. It could be, but mostly these are black or dirty from oil, as well as the tail interior. So, the shape looks nice, but some additional editing and texturing would be welcome.

The AFT cargo compartment. It is not a huge compartment, mainly intended for small luggage or boxes. All the walls are covered with a fabric-like texture, and even the crashnet is of the same material. I spotted three switches on the front wall, of which one was operative. When you’re inside, you can use the door handle to close and reopen this cargo door. If you like the texture used for the wall and ceiling coverage, that is a matter of taste. This compartment can also be reached via the cabin.

Since I haven’t seen any real photos showing the interior cargo compartment, I can’t judge whether the used texture material reflects the real Gulfstream model. The overall look looks good, but there is, in my humble opinion, some room for improvement.

The tail, with its horizontal and vertical stabilisers, rudder, elevators, static dischargers, and tail lights, looks OK to me. I didn’t check it against real measurements, but the same as with the other aircraft components, regarding the super-flush skin. But further on, the horizontal and vertical stabilisers, with the rudder and elevators, are well done. Some more weathering would be more realistic. A good example are the static dischargers on the outboard side of the elevators. It looks to me like any painting has been forgotten, since the static discharger and the mounting are all white!

Overall, I must say that from a distance that the modelled GLF550/650 looks great, but on closer inspection I conclude that additional 3D and texturing work is needed, and hopefully the eggshell disappears then, too. Let’s go inside and check out the virtual cabin and the flight deck.

Virtual Cabin and Flight Deck

To check the aircraft interior, I need to open the entrance door first, which, as you can imagine, is modelled to include the built-in stair. And that doesn’t look bad at all. Absolutely not. That it all looks shiny and brand new, I can imagine that with this kind of business or almost privately owned jets. And yes, I also see the less-used polygons at the top of the handrail, and yes, I would love to see when a few more polygons are used to make it look a bit more real, a bit more rounded. But I am also aware that more polygons means a possible drop in FPS (Frames per Second).

You enter the FWD galley, and although all the cuberts and the washbin are well modelled, you won’t find any animation of the drawers, cubert doors or the toilet door. The cabinet’s texture in this area looks to me like highly polished wood, which may be the case.

Cabin screenshots are from the GLF550

Walking into the seat area, I can only say that the leather-look seats, the sidewall panels, the carpet, the animated tables, and the windshades are all done, but it still misses a bit of exclusivity. Don’t get me wrong, Antoni tried to cover every part of the cabin, including some reading light controls and the previous animations, but since the cabin is really super exclusive in terms of the materials used and the additional animations, I would love to see this in the modelled GLF models too.

The end of the virtual cabin is more casual since you won’t find any large leather seats. Instead, you will find on each side of the cabin a fabric-covered bench. I noticed that on each side of this part of the cabin, you have one window; however, I only get one window shade to work with. Also, in this part of the cabin, there is some lighting control, and that’s it. No further animations in this section. And although you are looking at the lavatory door at the back, no animation from this door either. By the way, cabin lighting control can be done via the AKD Studio tablet.

Cabin screenshots are from the GLF650.
The last two screenshots show the cabin light controlled from the AKD Studio tablet

Although the above description is from my virtual GLF550 cabin walk, and knowing that the layout and animations in the GLF650 are different, the overall look and feel of the two types are basically the same. There is a clear difference between the GLF550 and GLF650 models when you look closely at the virtual cabin. Lots of things are the same, but for example, the lighting control is different, whereas the GLF550 has extendable tables; I didn’t see this in the GLF650.

It’s time to move back to the front and explore the cockpit or flight deck. But first, some words about whether the GLF550/650 has a cockpit or flight deck. Checking many official webpages, it turns out that all are talking about a flight deck, or to be precise, the GLF550/650 was introduced with the Honeywell PlaneView flight deck, a cockpit that redefined pilot ergonomics and safety. It comes with four large 14-inch displays for advanced flight data visualisation, an enhanced Vision System (EVS) for greater approach precision, a Head-Up Display (HUD) integrated with synthetic vision and an automatic Descent Mode for additional safety redundancy.

Let’s check out the modelled 3D flight deck, but first, one thing you need to know: I was positively surprised that this was taken into account. The GLF550, or the real one, is an older model than the GLF650/650ER. Later, I will tell you more about the old-fashioned cable system used to control the primary flight controls in the GLF550 versus the Fly-by-Wire system installed in the GLF650/650ER. That said, the overhead panel, centre pedestal and main instrument panels are not the same. The overhead panels are different, although not huge differences, but they are there.

Example screenshots of the GLF550 Flight Control Trim Cable System

More differences can be found on the centre pedestal and the glareshield. I compiled some screenshots with the AKD Studio GLF550 on the left and the GLF650 on the right. Interesting to see how much effort goes into replicating these different models.

The reason I mention this is that I did a thorough check of how these 3D GLF models are made, and, in terms of quality and realistic look and feel, they are basically the same.

Modelled Flight Deck
When you enter the GLF550/650/650ER, you get the impression that it all looks clean and unused, or, as we say, hardly any or no weathering at all. The reality is that these types of exclusive business jets are maintained at the highest level. Ok, you’ll see some weathered spots over time, particularly on the Auto Flight panel and the centre pedestal. Ok, now the modelled AKD Studio GLF models.

The overall 3D modelling is well done. Let’s be honest about that. That some parts could use an overhaul or some refinements doesn’t mean it is not good. I am talking, for example, about the 3D screws that connect the panels to the frame. I also noticed that the text near each circuit breaker is not as sharp as the text on the other panels. Or I am talking about using fewer polygons, with the result not a nicely round screw, a hole or something else.

That I feel all the panels lack a bit of use/weathering is partly personal, but some small weathering would give the panels and the overall cockpit a more realistic look and feel. On the other hand, I am impressed by the sharpness of all the text near each switch, rotary selector, and other components. And, when I look at these rotary selectors, or knobs, wow, they look awesome; well done.

Perhaps surprisingly, there is carpet on the floor, and against the sidewalls of the centre pedestal. Weird? Yes, unexpected, but normal for these aircraft models. The only thing with these used textures is that they are flat; there is no sign of a 3D effect, or the used NRM files are set too low. This is also clearly visible when you step up from the cabin floor onto the cockpit floor.

Another suggestion I found is that the construction of all panels, sidewalls, centre pedestal walls, and pilots’ and observers’ seats is, in particular, so dull. Perhaps some semi-gloss would give it that extra realistic look unless I am mistaken and this is so as the real model is. That the seat frame doesn’t have all the screws is just a minor detail and not worth adding all those polygons.

At the entrance to the flight deck, on your right-hand side, you have the 3rd seat without animations, unlike the pilot seats, which have animated armrests. Above the observer seat, you will find the Quick Donning oxygen mask, which, by the way, is well modelled. Besides the animated pilot seat armrests, you have the sun visors and, of course, the HUD (Head-Up Display).

Another item to bring to your attention is the two CCD (Control Cursor Devices). The pilot’s and copilot’s CCDs are required to manipulate the menus generated by the CMC (Central Maintenance Computer), if simulated, but this is not applicable at this writing for the AKD Studio GLF models.

Each CCD is located on the left and right side panels in the cockpit. The CCD comprises a cursor positioning device that controls menu selections. The rotary dial controls the main menu selections (by moving the green bar), and the “enter” button finally selects the highlighted function.

I know from Antoni that he plans to overhaul the aircraft’s 3D parts, including the cockpit. Although there’s always something to say about how a 3D cockpit is modelled, more important is how the simulated systems are modelled compared to the real aircraft, and how realistic it flies, right?

And now it is time to power up the systems and see how it looks then. I am “again” impressed. And yes, the main DUs are the four on the centre panel. Oh yes, you’ve got the FMS MCDUs, but further the flight deck is relatively clean except for the GLF550, which has standby indicators in the middle of the centre instrument panel. The GLF650/650ER has the electronic version on the glareshield.

So, you won’t find any other indicators spread across the flight deck; all centralities are on the DUs. OK then, one small indicator on the overhead panel, related to the cabin vertical speed. That said, it is a clean flight deck with many display units, not too many switches, and, as far as I was able to check against some manuals I found on the Internet, these DU units are heavily detailed in the modelled GLF aircraft. This is pure own programming. Very nice to see.

These screenshots represent the GLF650 model

The GLF550/650/650ER are equipped with the Honeywell PlaneView electronic cockpit display system. These DUs provide the crew with visual presentations of instrumentation and navigation information. Display information includes:
– Primary flight displays (PFDs)
– Navigation displays
– Synoptic displays
– System displays

Due to the absence of a system manual or the difficulty of finding an FCOM (Flight Crew Operating Manual) or AMM (Aircraft Maintenance Manual) online, I cannot verify whether every aircraft system is modelled as it functions in real life. I can check the system’s behaviour using the AKD Studio YouTube videos, but that is no guarantee the system behaves the same way in real life. On the other hand, I do believe that Antoni tried to replicate each system as closely as possible.

These screenshots represent the GLF550 model

Then some words about the 2D pop-ups.
For all DUs and the three MCDUs, you have pop-ups. Let’s start with the MCDUs. You either click the MCDU itself or you select it from the AKD Studio X-Plane menu. For the DUs 1, 2, 3 and 4, you can only get the 2D pop-up via the X-Plane menu. There’s no option to click anywhere on the built-in DU. When you have a connected 2nd monitor or another screen, you can drag a pop-up DU to it. I am impressed by the overall quality and sharpness of the pop-ups. They offer razor-sharp images.

. The first two screenshots are the available pop-ups of the GLF650. The last screenshot represent the GLF550 2D pop-up MCDU / Display Controller

Implemented Auto Flight Systems
During one of my emails with Antoni, we discussed the depth of system programming, with a particular focus on the Auto Flight systems. Antoni informed me that, “Regarding the Auto Flight system, it is difficult to define precisely how closely every aspect matches the real system. All autopilot modes are implemented and functional, although I continue to refine, correct, and improve the system with each update. The MCDU is fully custom-built and is designed to operate like the one in the real aircraft. However, not every MCDU page is available yet. I will continue adding missing pages and improving the existing MCDU components in future updates.”

Flight Management System and Flight Plans

Flight Plan Sources – Navigraph
Well-known and fully integrated with the AKD Studio GLF aircraft is Navigraph/simBrief. When you want to use SimBrief without updated Navigraph AIRAC cycles, you first need to create a free SimBrief account to get access. This account is made via the Navigraph website. After you have created a free Navigraph account, you can use the same account for SimBrief. I would suggest that, if you haven’t already, you get a Navigraph subscription.

This subscription provides access to AIRAC cycles, but Navigraph offers much more. For AIRAC cycles and related services, you need a payware account with Navigraph. And yes, it costs roughly 100 euros, but it is worth every euro or whatever currency you are using to pay with.

Flight Plan Sources – Little NavMap
Another interesting offline planning tool is the freeware program LittleNavMap. The program is compatible with Windows, macOS, and 64-bit Linux. Although LittleNavMap offers much more than just flight planning, it still requires up-to-date AIRAC cycles, so a Navigraph account is a must. Something else to keep in mind is that the AIRAC cycle of the created flight plan must match the AIRAC cycle you use in X-Plane, or you get a mismatch warning.

Then, as I mentioned before, it’s essential to have up-to-date SimBrief performance files. For this you search for this GLF550 link or for the GLF650/650ER this URL. Look on each applicable page for SimBrief profile. When you click either, you end up on the dedicated SimBrief aircraft page with all the relevant GLF data. Click “Save Airframe”. When you create a SimBrief flight, you can select the GLF550/650/650ER profile you just added.

Your Flight Plan
You can enter a flight plan manually, waypoint by waypoint; or you can load a SimBrief flight plan. According to Antoni, “Yes, in the Full Flight Tutorial for both aircraft, I explain how to enter a flight plan manually, waypoint by waypoint, as well as how to load one using the Datalink function.” Here are the different YouTube links (add https:// in front, and you’re directly guided to the video)

GLF650 by AKD Studio | OFFICIAL FULL FLIGHT TUTORIAL
GLF650/550 by AKD Studio | DEMO FLIGHT: RNAV Approaches and new features
GLF550 by AKD Studio | OFFICIAL FULL FLIGHT TUTORIAL

Antoni continues, “The tutorials are divided into chapters, so you can easily find and jump directly to the section you are interested in.”

Which Hardware to Use?

The real aircraft comes with a standard control wheel model. This means there’s a lot of hardware available that uses the control wheel, including the Honeycomb Alpha and the Thrustmaster Boeing set, from other manufacturers as well. When using a joystick, which is also an option but less realistic, you can use any joystick, and when it comes to throttle control, you can use any device for this. I used the Honeycomb Alpha Flight Controls paired with the Honeycomb Bravo Throttle Quadrant, which feels like the perfect combination to me. Add to this the rudder pedals from either Honeycomb or Thrustmaster, and you’re done.

Since it is not mentioned in any of the manuals, I decided to contact Antoni for this. He informed me that “As for hardware, that is a difficult question for me to answer. I personally use Thrustmaster equipment:
– Airbus Edition joystick
– Boeing Edition throttle quadrant.”

I am aware that I only highlighted a couple of hardware brands, but there are, of course, many others on the market, such as Thrustmaster, Logitech, Turtle Beach, and CH. When you are thinking of buying new hardware, it’s perhaps a good idea to check out our in-depth hardware reviews page.

A note I found in the AKD Studio Discord channel, under the FAQ section, is “How to operate the autothrottle in GLF550 and GLF650?” That’s worth checking out how Antoni explains this. In case you don’t use Discord, you can also watch how to correctly operate the autothrottle and TOGA in this YouTube tutorial. (youtu.be/oWABvcr2UCY?t=737&si=sNEKiSfoR0RI0tCR) Note: Add https:// to the provided link!

Finally, I would like to add to this “hardware” section that it doesn’t make much difference what hardware you use. Of course, a joystick isn’t fitted in the real Gulfstream, thus also not in the GLF models, but when you have nothing else, it works perfectly too. Most importantly, you can assign the axis to your needs.

Summary Part 1

I always try to keep the review as short as possible while still including all the necessary information, but I can’t. When I become enthusiastic about a product, I am in, and I continue, and so on. This has led me to split the AKD Studio aircraft models into Part 1 and Part 2 reviews.

Having completed the Part 1 review of the AKD Studio models, I am happy with the model’s 3D representation, both exterior and interior, but there is still some work to do in terms of texturing and 3D refinements. The fact that Antoni from AKD Studio implemented “save situations” is great. And let’s not forget that he also tried to implement the real Honeywell PlaneView flight deck, which is amazing.

As of this writing, July, 2026, this review covers the AKD Studio GLF 550/650/650ER aircraft version 2.26 for the GLF550, and version 1.07 for the GLF650 models. With this review and the screenshots I made, I used the following add-on software:

– Payware | X-Plane 12.4.3 r2
– Payware | Navigraph AIRAC Cycles and Charts
– Payware | World Traffic 3
– Freeware | AviTab
– Freeware | OpenSceneryX
– Freeware | XChecklist v1.52
– Freeware | clist.txt from Org xplanepeter1955.
– Freeware | clist.txt from Org user ELATES
– Freeware | FlyWithLua NG v2.8.14 for X-Plane 12
– Freeware | SkunkCrafts Updater v12.1r2 for X-Plane 12
– Freeware | BetterPushback 1.13
– Freeware | WalkAround for xplane

Interesting background: while reading one of the Gulfstream manuals I found online, I was surprised to find a big difference in how the flight controls are operated. While the primary flight controls – ailerons, elevators and rudder – in the GLF550 are operated via the old-fashioned way. This applies only when manual inputs are provided. The autopilot input is an electrical signal to the autopilot actuator, but it still uses the cable system to control the flight control surfaces. This is totally different from the GLF650/650ER, which is equipped with Fly-by-Wire.

Apart from the add-ons listed in Part 1 of this review, I hope you find the contents useful. I tried to cover different aspects, not always directly related to the AKD Studio GLF models, but also to provide additional helpful information. I hope I covered most of the GLF models so far, but I’m sure I have forgotten something. If I did, I could hopefully highlight it in the upcoming Part 2.

And now, heading for Part 2. As just mentioned, it will cover a complete “test or tutorial” flight using the AKD Studio full test-flight YouTube demo video as a guideline. As with many other Part 2 aircraft reviews I have done before, I intend to cover a full flight, divided by flight phase, as well as all other preparations and experiences related to the AKD Studio GLF aircraft model.

Hold on, some words about the Frame Rates of the GLF models. Given the complexity of the simulated systems, particularly the DUs, and the way they are modelled, I am impressed. On my MacBook Pro Max M4, it turned out that, e.g. at LFMN (Nice, France), I can easily reach between 45 and 60 FPS, depending on whether it is inside or outside the aircraft and, of course, depending on my settings and the weather conditions. But also the complexity of the airport, other AI traffic and so on.

The screenshots I took are just examples, and so are my settings. We all know that the actual FPS depend on so many other factors. That said, overall I am very happy with this.

See you soon!

Feel free to contact me if you’ve got additional questions related to this impression. You can reach me via email Angelique.van.Campen@gmail.com or to Angelique@X-Plained.com.

With Greetings,
Angelique van Campen

 

 

Add-on:Payware simMarket/AKD Studio GLF 550/650/650ER
Publisher | Developer:simMarket / X-Plane.Org / | AKD Studio YouTube
Description:Ultra realistic rendition of the Gulfstream 550/650/650ER
Software Source / Size:Download / Approximately 3.7Gb (unzipped)
Reviewed by:Angelique van Campen
Published:July 25th 2026
Hardware:- MacBook Pro M4 Max 14" / 64Gb RAM / 1TB
- Intel 3GHz Intel Xeon W / 4.5Ghz
- Thrustmaster TCA Captain Pack Airbus Edition
Software:- macOS Tahoe 26.5.2
- X-Plane 12.4.3

0 Comments

Submit a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.