The Perfect X-Crafts E-Jets Family

Part 1: My Introduction

Who is X-Crafts?
That success story goes back many years. X-Crafts is a well-known X-Plane developer and is especially prominent in the Embraer E-Jets for X-Plane X.

I started this introduction many weeks ago, almost months ago. Then I went on a long vacation to the Netherlands, Denmark, Germany, and back to France, to my home. In between, I underwent some retina surgeries, so altogether, this review has taken much more time than planned. And now, at the beginning of August, I try to finish this introduction, including Part 1 of the X-Crafts E-Jets Family review. Yes, I decided to split the review because the X-Crafts E-Jets Family are worth a thorough review.

This Part 1 review covers the E-Jets Family package, including its various aircraft models, exterior and interior expectations, operational procedures, and additional steps to follow. Part 2 will be dedicated to a comprehensive demo or tutorial flight, where I will break down the overall flight into its respective flight phases.

X-Crafts offers, as of today, not only the payware E-Jets v2, but also freeware E-Jets for both X-Plane 11 and X-Plane 12. And of course, there are differences between the freeware and payware packages. Curious what the freeware offers and what you miss when you decide to go for the payware E-Jets v2? Then check out these dedicated X-Crafts web pages. This URL is for the E-Jets cockpit differences, while this link explains more about the freeware package.

Are you ready for the X-Crafts E-Jets Family adventure?

Installation, Updates, Documentation, Settings and Liveries

Installation
I got my X-Crafts E-Jet Family package from Aerosoft. That said, the following procedures, as written below, are with Aerosoft’s One Installer. When you buy the package via X-Plane.Org, it will be a ZIP package. Whether the installation procedure you are using is a straightforward process, a serial number protects the product.

As mentioned, I installed the Embraer E-Jets Family, which contains all the aircraft models. This means one folder named “Embraer E-Jets Family” contains all the aircraft: the E-170, E-175, E-190, E-195, and the Lineage 1000. The package offers both X-Plane 11 and X-Plane 12 compatible models.

As just said, you must enter the serial number of an X-Crafts model upon selection at X-Plane start-up. Afterwards, you can select any Embraer models without entering the serial number again. Anyway, after you enter the serial, save it, reload the aircraft, and you’re done.

In addition to installing the aircraft, you need to install the following plugins:
First, the Skunkcrafts plugin. Second, the DrGluck Terrain Radar plugin. This plugin is available for both X-Plane 11 and X-Plane 12.

A quick note about the Skunkcrafts plugin: you also have a Standalone Client. The standalone client allows you to update the supported product without the need to start X-Plane.

Third, the AviTab version 0.7.1. You can grab your copy via this dedicated X-Plane.Org link or directly via the AviTab GitHub page.

And last but not least, you need the AIRAC cycles for your navigation. Let me explain that in detail for those new to X-Plane. AIRAC (Aeronautical Information Regulation and Control) cycles are aeronautical information which is constantly changing: airspace structures and routes are revised, navigation aids change, SIDs (Standard Instrument Departure) and STARs (Standard Terminal Arrival Route) are amended, and runway and taxiway information changes.

Although this paragraph was copied from the ICAO website, up-to-date navigation is also essential for the serious flight simmer.

Navigraph is the go-to source for everything you need for flight simulation. You must opt in for a Navigraph account. Once that’s done, you can select an Ultimate package on a monthly or yearly basis. You save 25 per cent with the annual account compared to the monthly subscription. But you could ask yourself, what do you get with this Navigraph Unlimited subscription?

You get everything needed for your navigation, e.g., AIRAC cycles, charts, and flight data planning. The charts option is fantastic, allowing you to check every airport’s charts for planning, background airport data, taxiing, SID, STAR, or anything else needed for your VFR (Visual Flight Rules) or IFR (Instrument Flight Rules) flight.

Check out their dedicated Navigraph product page. Add to this their flight planning, originally brought to you by SimBrief, but now an integral part of Navigraph, and you’ve got all that you need for realistic flight planning, including all belonging data.

Since SimBrief is an integral part of Navigraph, you can log in with the same credentials as your Navigraph subscription. But if you want to consider a Navigraph subscription, you can still use SimBrief separately, on a free basis. The only thing you need to do is create a SimBrief account.

Updates
The Skuncrafts updater keeps the Embraer aircraft family up to date. In the Embraer aircraft folder, you will find the skunkcrafts_updater.cfg file and a skunkcrafts_updater_beta.cfg file, which can also be found in the “Manuals” folder.

Documentation
The E-Jets Family documentation can be found in the Manuals folder. Currently, the Manuals folder only offers one Acrobat manual: E-Jets Family by X-Crafts—User Manual. I must say, it is a comprehensive manual. Everything you can think of is included in the 170-page user manual. This means you will find all the information about the modelled aircraft systems, the necessary plugins, getting started with the Embraer family, and so on.

And no, this user manual has no tutorial or separate section on the FMS (Flight Management Systems). However, X-Crafts offers an in-depth demo flight, supported by many videos, on its dedicated DEMO FLIGHT web page. I can tell you that it is very well-written and has high educational value.

During my Part 2 review, I will utilise the X-Crafts demo flight and describe in detail how helpful their demo flight web page is.

Settings via X-Plane menu
Although the settings section is a part of the X-Crafts manual, it is worth highlighting a couple of items. Plugins and Settings start on page 13 of the manual. It is accessed via the X-Plane menu E-Jets Family xxx, where xxx stands for the X-Craft loaded aircraft type. In addition to the technical support and FAQ menu options, you can select several 2D pop-up windows. More about this later.

Then you have the X-Plane menu option EFB (Electronic Flight Bag), which, for clarity, refers to the X-Crafts EFB, not the AviTab EFB. This is double since the aircraft itself comes already with a built-in EFB, mounted at each the sliding windows. The menu EFB offers a pop-up window of the EFB. This could be handy when you can move the popup EFB to a separate monitor. The pop-up EFB is sizable and offers several tabs, including Ground Services, Weight and Balance, Takeoff Performance, Landing Performance, Checklists, Settings, and AviTab.

As you can see from the above screenshots, you have the option to use either the built-in EFB or the floating pop-up window. The different EFB tabs speak for themselves, but don’t worry, some of them we will use during our test flight. But it must be said that the User Manual, starting on page 14, offers an in-depth explanation of what the EFB provides and how to deal with it.

Liveries
The E-Jet package comes with a couple of liveries, of which three are dedicated to the Lineage 1000, but don’t worry. Many user liveries have been painted and can be found, for example, on the dedicated X-Crafts E-Jet Family X-Plane.Org website. You won’t find many liveries for the Lineage 1000, as it’s a business jet with a relatively small fleet. All the available liveries at the Org website are a mix of real and fictional liveries. Nonetheless, it is amazing how many real or fictional paintings have been painted.

Now it is time to delve into some background information about the actual Embraer E-Jets.

Real Embraer E-Jet Family

The Embraer E-Jet family is a series of four-abreast, narrow-body, short-to-medium-range, twin-engined jet airliners designed and produced by Brazilian aerospace manufacturer Embraer.

The E-Jet was designed to complement Embraer’s earlier ERJ family, the company’s first jet-powered regional aircraft. With a capacity of 66 to 124 passengers, the E-Jets were significantly larger than any aircraft Embraer had developed before that time. The project was unveiled in early 1997 and formally introduced at the 1999 Paris Air Show. On 19 February 2002, the first E-Jet prototype completed its maiden flight, and production began later that year.

The first E170 was delivered to LOT Polish Airlines on 17 March 2004. Initial rollout issues were quickly resolved, and Embraer rapidly expanded product support to achieve better global coverage. Larger variants, the E190 and E195, entered service later in 2004, while a stretched version of the E170, the E175, was introduced in mid-2005.
The E-Jet series achieved commercial success, primarily due to its ability to serve lower-demand routes while offering many of the amenities and features of larger jets. The E-Jet family is used by both mainline and regional airlines worldwide, with particular popularity among regional airlines in the United States. It also served as the foundation for the Lineage 1000 business jet.

In the 2010s, Embraer introduced the second-generation E-Jet E2 family, featuring more fuel-efficient engines. However, as of 2023, the first-generation E175 remains in production to meet the needs of U.S. regional airlines, which are restricted from operating the newer generation due to scope clause limitations.

The best and reliable source for background information is, of course, the official Embraer website. And, of course, Wikipedia also offers a wealth of information about the “E2” version, but for me, the most comprehensive source is the official Embraer site.

Walk-Around Check

Which Model?
Now the real work can begin, but hold on, the package comes with different models, so which one should I choose, or is there perhaps not much difference between these external models and their flight decks? This could be because it is also observed in other manufacturing brands, such as the Airbus A320 Family members.

The first question to answer is: on which model should I perform my walk-around check? Before I decide to do that, let me highlight the following: The E-Jets have up to 95% commonality in parts and systems across the four main types, which reduces rotable inventories and maintenance costs. The flight deck has 100% commonality across the four models, so they all require cross-crew qualification. The E-Jet family is subdivided into the E-170/-175 and E-190/-195, with the aircraft being certified as two main types, each with two variants. The smaller E-170/-175 are powered by the CF34-8E engine, rated at 14,500 pounds of thrust, while the larger E-190/-195 is powered by the CF34-10E, rated at 18,500 pounds of thrust.

And finally, some words about the Lineage 1000. The Embraer Lineage 1000 is a variant of the Embraer 190 regional jet airliner, launched as a private jet. The Lineage was advertised as an “ultra-large” business jet with seating for up to 19 passengers. It has added fuel tanks in the lower deck cargo hold space, nearly doubling the jet’s range. It boasts a lavish interior, divided into up to five sections, including an optional bedroom, a washroom with running water, and a walk-in cargo area at the rear. Since it is based on the E-190 model, the cockpit is almost similar; it is easy for the flight crew to transition between the Embraer E-Jet models.

Knowing this, I use the Lineage 1000 from VistaJet Germany for the remainder of this part 1 review.

Walk-Around Lineage 1000
My very first impression of the Lineage 1000, which is, to be honest, also applicable to all the other E-Jets members, is ‘wow!’ The level of detail is enormous. Let’s take the NLG (Nose Landing Gear) as an example to start with.

The NLG strut and linkages exhibit clear signs of wear, a weathered appearance, and visible dirt or old grease. Hydraulic lines for the steering cylinder and wiring haven’t been forgotten. Mounted decals (stickers) are razor sharp, and let’s not forget the unbelievable amount of details of the nose wheels. Then we have the light bulbs and their brackets. Another item that makes this NLG as real as it gets. And last but not least, the NLG doors include maintenance information on the fixed small doors, specifying the required torque for certain nuts and tire pressure.

These tiny details are also applicable to the MLG (Main Landing Gear). Yes, they are a bit larger, but the overall level of detail remains the same. Add to this the numerous decals, such as the GROUND connection, service charts, and the LIEBHERR identification plate. Excellent, since you can read what’s on these decals. But there is much more. Again, a nicely weathered strut with torque links and other linkages. On the rear of the strut, you will find the hydraulic lines, wiring for the brake temperature sensors and the tire pressure sensors.

You will even see the brake wear pin indicators. The outboard main wheels cover the wheel well when retracted, using the same design as the Boeing 737 Series. This main wheel features an aerodynamic plate, which, as expected, is weathered and dirty. By the way, you can also deselect the aerodynamic wheel covers from the X-Crafts EFB.

And when you think this is it, take a look at the stainless steel bands around the MLG strut, the clamp with rubber that secures the hydraulic lines, and even the hydraulic lines have a colour wrapping around them identifying which system, what fluid and in which direction the fluid is going.

What makes me so happy is the unbelievably sharp decals on the exterior parts of the aircraft. Wherever I look, everything is sharp and readable. You see this near the landing gears, near the passenger doors, on the engine cowling, around the cargo doors, and so on.

Talking about animated doors. It is impressive to see how many tiny details are put into the operation and mechanism, including the hinges of the passenger doors and cargo doors. Before I continue, one thing first. On the Lineage 1000, only the FWD PAX and CARGO doors are animated. When you check the same on the other E models, you will notice that all PAX, service, and cargo doors are operational.

Let me take, as an example, the FWD PAX door on the left-hand side. You can control the opening/closing of the door via the EFB or by directly clicking on the handle. When opening the door, the handle moves slowly, and the VENT valve opens simultaneously. The door then opens in a controlled movement. When fully open, you can see the latches, stops, guided slots and the support handle mounted in the door frame.

This Lineage 1000’s “eye for details” is essentially the same for both the FWD cargo door and the interior of the cargo hold. A lot of time and effort is invested in the look and feel of areas that aren’t immediately apparent.

And then the engines. What I have seen so far is also applicable to the engine cowling, inlet, pylon, and exhaust. It appears that a large number of polygons (interconnecting lines) are used to create a realistically looking round inlet nose cowling. It is always up to the developer to decide how and where to use more or fewer polygons, as too many polygons can reduce the FPS (Frames Per Second).

For example, I like the inner nose inlet sound reduction material, which features grey plates with all the holes. It looks soooooooo realistic, wow! And it doesn’t cost any frame rates. It is just a matter of the right texture that shows this.

The walk-around check began at the nose section. I had a good view of the overall modelled Lineage 1000, which is the E-190 and all the models in this package. All are modelled, yes, I know, I have said it many times, with an eye for all those tiny details, including the correct dimensions to reflect as realistically as possible an Embraer E-Jet.

While walking along the leading edge of the wing towards the wingtip, the slats and their tracks are nicely modelled. At the wingtip, the navigation and strobe light units are of high quality. Since I extended the slats, flaps and spoiler panels, I have a good view of the flap track assemblies. And that’s the same, and perhaps with even more details, the spoiler panel hydraulic lines, wiring and actuators, all mounted at the wing trailing edge.

And finally, there’s the tail. A good view of the APU (Auxiliary Power Unit) exhaust, the air inlet, the many static dischargers on the elevator and rudder, the stabiliser position marking and much more.

Overall, a beautifully modelled Lineage 1000, but the “gorgeous” is also applicable to the other Embraer E-Jet models.

Ground equipment, cabin, and Flight Deck

The X-Crafts E-Jet models come with some internal and external animations and/or ground equipment. The ground equipment items for all models are the GPU (Ground Power Unit), the REMOVE BEFORE FLIGHT red flags, the engine inlet covers and safety cones. The animations depend on the aircraft type, specifically between the Lineage 1000 and the other E-Jets aircraft.

The Lineage 1000 offers animations for the FWD PAX door with integrated stair and the FWD CARGO door. For all the other E-Jet models, the left-hand FWD (without integrated stair) and AFT PAX doors are animated, as well as the right-hand FWD and AFT service doors, and both cargo doors.

If you are looking for a pushback truck, I recommend the latest version from BetterPushback. Just as a side note, in the following screenshot, you see a fuel truck, but this does not belong to the X-Craft ground equipment. I also included a screenshot of the animations for an E-Jet aircraft.

Some words about the BetterPushback Mod plugin. If you’re looking for a pushback truck that delivers an “as real as it gets” experience, consider the Better Pushback Mod. It is a fantastic freeware addition to animate this type of ground equipment. It is easy to control and works flawlessly with X-Plane. And almost forgotten, you can, of course, use the built-in pushback function from X-Plane itself, but that is basic and without any animation. The choice is yours.

Via the well-modelled FWD stair, I would like to check out the Lineage 1000 cabin. As expected for this business jet, the interior cabin and all that belongs to it gives me already a WOW effect, but hold on, I need to check out more. There’s so much to see: relaxing chairs, beautifully modelled cabinets, a nice virtual carpet, sleek overhead bins, and different sections with, in some places, even a bed. Static monitors, so no animated images, are positioned throughout the cabin.

I must conclude that a lot of time and effort is put into the creation of such a virtual cabin. Although the toilets aren’t animated, the sliding doors from the FWD pantry to the cabin are animated, as well as the individual tables in the cabin, and the lamp units above the bed. But there’s much more. Everywhere in the cabin, you have individual light control panels, the light units in the ceiling are controllable and adjustable, and the window blinds can be controlled smoothly as well.

And while I am busy with animations, let’s not forget this one. X-Crafts has implemented a pre-departure slide show, which can be personalised. After the FMS is programmed, the TVs display flight information, and you can also individually switch to Avitab to display the maps. If you have Avitab Web installed, you can then even browse the internet on any one of the TVs in the cabin! So, a lot of additional animations.

Since it is a business layout, there are no overhead bins in this model. To make this clear, the cabin is awesomely modelled with an eye for many details. The absence of animations doesn’t reduce my feelings for what X-Craft has created. Well done!

I mentioned the Lineage 1000 FWD PAX stair before, but it is worth highlighting again. When the stair is retracted and the PAX door is closed, the stair is folded and stored along the inner side of the left-hand cabin. Once you open the PAX door and pull out the folded stair, it unfolds and folds ultra-realistically outside. The area where the stair was stored is even well modelled with tiny details.

Although I decided to review the Lineage 1000, I would like to offer you a quick look at how the other E-Jet cabins look. They are, of course, different since we are dealing with cabins used by commercial airlines; nevertheless, everything that you can expect in such a commercial airline cabin is modelled. Via the FWD or AFT PAX door, you first reach the pantries. Well modelled, and the 3D artist didn’t forget to include all tiny details, such as the stickers on how to operate “something”, the cabin entertainment, and the lighting panel. Although the following screenshots are taken from the E-190 with KLM Royal Dutch Airlines livery, the way it is modelled is the same for all other models.

And then it is time to check out the modelled 3D cockpit or flight deck. I entered the flight deck via the open cockpit door, and yes, I had the same feeling when I entered the cabin; I got the ‘WOW’ effect immediately. The first screenshot below may look a bit weird, but it’s shot on purpose. The pilot seat tracks and seat frame are visible, and the floor panels have numerous weathered spots. But there’s, of course, much more to see from this angle. The seat frames are complete with tiny details, which are also applicable to the pedestal.

When I look from this lower position to my left and right, I can see many other panel parts, such as the circuit breaker panels and the fire extinguisher. On the left-hand side, I notice the foldable third seat, protection mask, and more. The 3D artist did a great job of balancing the number of polygons, ensuring it’s not too many but still enough to make it as realistic as possible.

From one of the side consoles, I have a lovely view of the instrument panel with the mix of virtual fabric-leather pilot seat cover, the controls, the DUs (Display Units), the seat straps/belts, the area below the glareshield, etc. The typical Embraer control wheel is well modelled, although it doesn’t offer any weathering. Although it lacks a weathered look, all the tiny buttons and switches are included. Nice to see how realistic it looks. And then the pedestal. This looks clean, slightly weathered but not too much, with, as it seems to me, many polygons to give the handles or throttle levers a smooth shape.

Even from this position, I am already impressed by everything, and this impression is reinforced when I look closely at the main instrument panel and centre section. And everything means the sharpness of the decals, the sharpness of the DU images, as well as the perfect readability of all other instruments.

Before moving to the overhead panel, I have a quick look at the lower side of the glareshield panel. Perhaps you won’t check it or forget to check it out yourself. If you already have the X-Crafts package, I encourage you to take a look. It is not just a plate. It is almost the real glareshield lower side, complete with wiring, screws, the plastic cover from the glareshield itself, the lighting units, and so on. The front of the glareshield, the Auto Flight system, offers sharp buttons with minimal weathering.

And finally, the overhead panel. The panel comes with clearly visible scratches, some spots of often-used selectors, buttons or switches, while the overall text on the panels is sharp and beautifully lit from the back. Wherever applicable, the red guards over the switches are particularly lovely to see, mainly when you operate them.

Then some words about the 2D pop-up displays.
But first this …….
The EDS (Electronic Display System) is an advanced system that displays primary flight, navigation and system information (taken from a real Aircraft Systems Manual). It is comprised of:
– Five identical Display Units (DU)
– One Guidance panel located at the glareshield
– Two Cursor Control Devices (CCD) mounted near the MCDUs
– Two Multi-function Control Display Units (MCDU)
– One EICAS FULL panel
– Two Reversionary panels.

The E-Jets are equipped with several 2D pop-up panels/displays. Let me be more precise: the popups are for the PFD (Primary Flight Display), MFD (Multi Function Display), EICAS (Engine Indication and Crew Alerting System), and FMS (Flight Management System), and, only applicable to the Lineage 1000, a lighting panel. You can get them either by clicking the respective flight deck display or via the X-Crafts X-Plane menu E-Jet Family xxxx – X-Crafts Popup Panels.

Once you have a pop-up DU or panel, let’s assume you have chosen the PFD. In the left-hand upper corner, you can lock its position on the monitor, or you can make it a floating panel. As shown in the previous screenshot, it can be moved to another monitor. To cancel the pop-up, you click the “X” located in the right-hand upper corner or click the DU in the instrument panel. And, you can resize them. Place your mouse at the bottom right corner of the pop-up panel, hold down the left mouse button, and drag down to increase or decrease the size of the panel.

And are there any animated flight deck objects?
Oh yes, there are.

As mentioned earlier, the cockpit door is animated, and the captain and co-pilot seats do have control switches, but it seems this is not working. Both armrests are animated on each seat simultaneously when clicked, and you can swivel the EFB in several directions as well as let it disappear. Then there’s the foldable third crew member seat, movable sliding windows, the speedy sliding side windows, sunvisors, an ON/OFF green sunvisor near the flash lights. By the way, the flashlights on each side panel near the floor can be removed and will switch on automatically. If you are looking for a HUD (Head Up Display), sorry, it is not implemented yet, but it might be added in the future.

An Operation Flight Deck

Now that we have seen how the 3D cockpit was modelled, it is perhaps a good idea to check out what it looks like when electrical power is connected to the aircraft. Besides that, it is also worth checking out which switches are operational, as far as possible. In part 2, during my demo flight, I’ll provide much more in-depth information.

Back to the current situation. I could connect the GPU (Ground Power Unit) to the aircraft, but I decided to start the APU (Auxiliary Power Unit). It allows me to test how the aircraft systems work together. Typically, I would say I use the SOP (Standard Operating Procedures) that I have, but since it’s not included in the X-Crafts user manual, it’s not a fair guide to use.

First, switch on battery 1. This gives me an operational MFD and EICAS. With the EICAS DU available, I can monitor the APU RPM and the EGT (Exhaust Gas Temperature). After the APU is up and running, I checked the MFD ELEC page, where I can see that all electrical buses are powered except for DC ESS 2. Switching on battery two will also power the DC ESS 2. Once the APU generator supplies the whole network, I check out all the switches and selectors on the overhead panel.

Besides a couple of non-functional switches, such as those on the DVDR (Digital Voice Data Recorder) control panel or the windshield wiper timer function, I can say that 90 to 95 per cent of the switches and selectors related to the aircraft systems are simulated. But knowing this, I am still impressed by the presentation of images on the different DUs, and also on other instruments like the IESS (Integrated Electronic Standby System), as well as the integral lighting of all the sub-panels.

And although it may be normal for all of us that 2D pop-up DUs exist with other developers, it is not as common as you think. Upon examining the last screenshot above, we can conclude that the 2D popups, such as those of the PFD and MFD, are of superior quality. And what happens with the flight deck lighting when we reach sunset or sunrise conditions? That’s another story, what I would like to share with you.

Not so many words are needed to explore an illuminated flight deck. It is just awesome. So, how can I conclude this section …… overall conclusion: Wow!

Need to know ….. Modelled Auto Flight Systems

During one of my email conversations with Marko from X-Crafts, we discussed the depth to which systems are programmed, with a particular focus on the Auto Flight systems. Marko informed me that “You might notice that the left and right MFD and PFDs are currently not individual. We are reserving this and other pilot-specific features for a future PRO version. The FMS units are individually modelled. What we haven’t implemented is two separate autopilot sources, which is why both PFDs are the same. The E-Jets are incredibly complex and automated, so from the start, we’ve had to prioritise the most critical features that the community would benefit from.”

As I delve deeper into the modelled systems versus the manuals, I will attempt to explain what is included and what is postponed to the Pro version. As Marko said, “Spending months on separate autopilots would not make a huge difference to the majority of our users as most people would only fly with one autopilot anyway, but it would postpone other features that everyone uses, like FMS Speed, ILS Autotune, Glide Path mode, etc.”

And last but not least, Marko informed me that “We are currently working on something that many users have been asking for years. We can now create our own custom LNAV, which allows us to implement holds, flyover waypoints, and other patterns for future use. This is planned for one of the future updates later this year.”

A Couple of Things

AviTab support
As you see with many add-on developers, the X-Crafts E-Jets v2 has complete integration with the AviTab (Aviation Tablet). When I write completely, I mean not only the AviTab device with its basic functions but also SimBrief integration, TO and LDG data tabs, Weight and Balance tab, as well as a direct vice versa link with the X-Crafts EFB (Electronic Flight Bag). The X-Crafts EFB is positioned on each sliding side window. Very convenient for you as a virtual pilot, especially when using VR. However, if the X-Crafts EFB position is the same as the real E-Jet, I’m not sure. It isn’t easy to find photos, and perhaps it is even a special requirement for airliners.

As briefly mentioned before, AviTab has the option to link your Navigraph account to the tablet. This allows you to download charts directly to your AviTab. When you have other documents related to your X-Crafts aircraft, copy them into the designated AviTab folder. It will then be all available via the AviTab for your cockpit preparations.

Once the AviTab plugin has been copied to the correct location within X-Plane Resources/Plugins folder, you will see the AviTab content on the left-hand and right-hand side windows in the AviTab frames.

To make one thing clear about the AviTab and the X-Crafts EFB. These are two separate products. The only thing they have in common is that the X-Crafts EFB can be implemented in the AviTab if this plugin is installed. When you haven’t installed the AviTab plugin, you always have the pop-up X-Crafts EFB or the same tabs in the side windows mounted frame. This frame is an empty AviTab.

Which Checklist
The X-Crafts EFB has a checklist tab. Although it does offer detailed steps to follow, it is not linked to an aircraft system. This means it is just a static checklist. When you do something, for example, on the overhead panel, there’s no feedback to this checklist. Therefore, I would suggest that when you prefer to use an interactive checklist, you use the clist.txt file with the XChecklist plugin. Curious about this option?

Check out the clist.txt file and PDF version from Org user jengle and the XChecklist plugin maintained by Org user sparker.

The default red colour in the interactive checklist, as shown in the screenshot, is not the most suitable colour, but it can be changed to your preference.

Flight Plan Options
The X-Crafts E-Jets work with the X-Plane flight plan extension FMS. You have two options to create FMS flight plans: either by using an offline or online program, or by entering all the waypoints step-by-step in the FMS MCDU.

Let’s explore the freeware options available to save the flight plan with the FMS extension. As just mentioned, if you prefer not to use a flight plan program, you can create a flight plan directly in the FMS MCDU. I will explain that later; however, it is normal that pilots select a company route from the MCDU. For pilots, there is no need to enter all waypoints into the MCDU, except for the SID (Standard Instrument Departure), STAR (Standard Terminal Arrival Route), and any necessary changes.

Well-known and fully integrated in the AviTab is Navigraph / simBrief. When you want to use SimBrief without updated Navigraph AIRAC cycles, you first need to create a free SimBrief account to get access. This account is made via the Navigraph website. After you have created a free Navigraph account, you can use the same account for SimBrief.

A better option is to go for a Navigraph subscription. This subscription provides access to at least the AIRAC cycles, and much more. For AIRAC cycles and much more that Navigraph offers, you need a payware account with Navigraph (https://navigraph.com/).

Another interesting freeware offline planning tool that I’m using besides SimBrief by Navigraph is the freeware program LittleNavMap. It can do much more than just flight planning. The program is compatible with Windows 7/8/10/11, macOS 10.13+, and Linux 64-bit. Keep in mind that Little Navmap also needs AIRAC cycles, so an account with Navigraph is a must!

Another thing to keep in mind is that both AIRAC cycles are the same. Oops, what do I mean? The LittleNavMap and the X-Plane AIRAC cycle must have the same cycle number.

Additionally, it’s essential to know about the presence of LittleNavMap performance files. That said, don’t forget to download from the Little NavMap website the X-Crafts E-Jets Family performance files. As far as I could see, there’s no specific performance file for the Lineage 1000, but since the Lineage is derived from the E-190, I suggest using that file.

Creating a Flight Plan
Those simmers who don’t prefer to use the “ready to load” flight plan described in the previous paragraph can manually enter the flight plan into the MCDU, waypoint by waypoint. When you want to do it manually, my advice is to use the X-Crafts demo flight starting at section 2. Entering Route (RTE page).

I can’t emphasise it enough, having previously worked as a technical instructor for KLM Royal Dutch Airlines and Lufthansa Technical Training, I am impressed by the extensive documentation and videos X-Crafts offers its customers. Please Use It! It is excellent material!

Which Hardware to Use?
When using a joystick, you can use any joystick, and when it comes to throttle control, you can use any device for this. I used the Thrustmaster TCA Airbus side-stick, but you can use the Saitek X-52 or, when you own a control wheel device such as the Honeycomb Alpha Flight Controls in combination with the Honeycomb Bravo Throttle Quadrant, it will all work with the X-Crafts aircraft.

I am aware that I only highlighted these brands, but there are, of course, many others on the market, such as joysticks, throttle controls or combined packages from Thrustmaster, Logitech, Turtle Beach, CH and others. When you are thinking of buying new hardware for the X-Crafts E-Jets Family, then it’s perhaps a good idea to check out our in-depth hardware reviews page.

I decided to give it a shot and used my Thrustmaster TCA Airbus set. I was aware that this hardware is dedicated to twin-engine Airbus aircraft, but on the other hand, it should work with the X-Crafts Embraer models too, perhaps with some minor differences. As expected, I could assign most of the switches and selectors, but since the Airbus uses slightly different steps, some assignments are not 100 per cent accurate. A good example is the FLAP lever.

The available steps on the Thrustmaster FLAP lever are different from the steps in the Embraer models. It’s not a big deal; you need to be a bit flexible. I also found that the precise throttle assignment is not easy. Assigning the throttles on the TCA Throttle Quadrant to X-Plane is straightforward, but fine-tuning is complicated because the X-Crafts EFB doesn’t have the option to fine-tune throttles and reverser “points”. This means in practice that with the throttles on the TCA quadrant in IDLE, the X-Crafts EICAS could show the amber REV. Not all of these are major issues, but they’re worth keeping in mind. I am also unsure if they’re related to macOS.

How about Frame Rates?
Although I will highlight available FPS during my demo or test flight in part 2, some words right now will be a good idea. With such complex aircraft, you can expect a reduction in FPS. As always, it depends on many things. What are your PC or Mac specifications? Perhaps just as important, what are your X-Plane settings? Then, it also depends on whether you are loading an add-on airport, the weather conditions, and whether it is daylight, twilight, or night. And not to forget, which X-Crafts settings have you made?


The above screenshots are taken from my MacBook Pro M4 Max.

I can’t judge how the X-Crafts E-Jets Family performs on a Windows PC, but I can on two types of different Apple computers with the latest macOS Sequoia installed. That’s on an iMac Pro with an Intel Xeon CPU in combination with the Radeon Pro Vega 64. The other Apple PC is a MacBook Pro (MBP) with an M4 Max Silicon chip. The older iMac Pro can still perform nicely, but the MBP M4 performs great. I am not so interested in FPS of 50, 60 or even higher. There’s no need for that high, as long as X-Plane works smoothly.

Summary Part 1

I was afraid of it. The review has become a bit longer than I expected. Therefore, I decided to split the review into Part 1 and Part 2. Part 2 is then dedicated to the demo flight, including all the other preparations you can think of. Having completed Part 1 of the X-Crafts E-Jets Family review, I am impressed by the model’s 3D representation, both in terms of the exterior and interior.

I explain why X-Crafts hasn’t decided not to include a complete dedicated split Auto Flight system. Instead, it comes with awesome manuals and lots of dedicated videos, including a demo or tutorial flight video. I believe having a robust documentation foundation, in any readily available format, is an excellent start for enhancing the Embraer models to the Pro version.

As of this writing, August 10th 2025, this review covers the X-Crafts E-Jets Family version 2.01. For this review and the screenshots I made, I used the following add-on software:
– Payware | X-Plane 12.2.1-r1 (logically)
– Payware | Navigraph AIRAC Cycles and Charts
– Payware | World Traffic 3
– Payware | Aerosoft EGNT Newcastle Airport / simMarket / X-Plane.Org
– Freeware | DrGluck Terrain radar + Vertical Situation Display
– Freeware | AviTab
– Freeware | OpenSceneryX
– Freeware | XChecklist v1.52
– Freeware | clist.txt + PDF
– Freeware | FlyWithLua NG v2.8.12 for X-Plane 12
– Freeware | SkunkCrafts Updater v12.1r2 for X-Plane 12
– Freeware | BetterPushback 1.10

With this list of add-ons from part 1 of this review, I hope you find the contents useful. I tried to cover different aspects, not always directly related to the X-Crafts Embraer package, but also provide additional helpful information.

For me, it is now time to continue. I start with part 2, which will cover a complete demo or tutorial flight using the X-Crafts demo YouTube movie as a guideline. I intend to cover a full flight, divided into each flight phase, as well as all other preparations and experiences dealing with an X-Crafts Embraer aircraft model. Based on my “writing and review” experience, I can tell you that this will be fun.

See you soon!

Feel free to contact me if you’ve got additional questions related to this impression. You can reach me via email Angelique.van.Campen@gmail.com or to Angelique@X-Plained.com.

With Greetings,
Angelique van Campen

 

 

Add-on:Payware Part 1 - X-Crafts Embraer E-Jet Family
Publisher | Developer:X-Plane.Org / Aerosoft / simMarket | X-Crafts
Description:Ultra realistic rendition of the Embraer E-Jets Family
Software Source / Size:Download / Approximately 8.42 Gb (zipped)
Reviewed by:Angelique van Campen
Published:August 10th 2025
Hardware:- iMac Pro
- Intel 3GHz Intel Xeon W / 4.5Ghz
- Radeon Pro Vega 64 16368 MB
- 64 GB 2666 MHz DDR4
- 1 internal 1TB SSD (Bootcamp Windows 11)
- 1 external 2TB LaCie Rugged Pro SSD (Sequoia 15.x)
- Thrustmaster TCA Captain Pack Airbus Edition
- Honeycomb Alpha Flight Controls
- Honeycomb Bravo Throttle Quadrant
Software:- macOS Sequoia (15.x)
- X-Plane 12.2.1

0 Comments

Submit a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.