Small but Mighty! X-Crafts ERJ v2 Family – Part 1

Introduction

Not so long ago, I was informed about the release of the X-Crafts ERJ v2 models. I decided to contact Aerosoft, and I received approval from X-Crafts to review this new Embraer package. And here we are … starting with Part 1 of the ERJ v2 Family review. I write Part 1, which means there will also be a Part 2. Part 1 will most likely already be a long, informative review. When I add a complex flight review to this, it will be too long; that said, the test flight will be Part 2.

Part 1 of this review covers the ERJ v2 Family pack, including its aircraft models, exterior and interior expectations, operational procedures, and additional steps. Part 2 will be dedicated to a comprehensive test flight, in which I will break down the overall flight into its respective phases. Besides that, I will add sections on what we call nice and what we need to know.

As of today, X-Crafts offers not only the payware ERJ v2 and E-Jets v2 but also some freeware products. First full functional E-Jet 175 and 195 for both X-Plane 11 and optimised for X-Plane 12. And of course, there are differences between the freeware and payware packages. Then, free E140 and E170 preview models.

Curious about what the freeware offers and what you miss if you do not go for the payware E-Jets v2? Then check out these dedicated X-Crafts web pages. This URL is for the E-Jets cockpit differences, while this link explains more about the freeware package.

Installation, Add-Ons and Updates

Installation
I got my X-Crafts ERJ Family pack from Aerosoft. This means that the installation follows the procedures from Aerosoft’s One Installer. (https://one.aerosoft.com/) When you buy the package via another sales point, it will most likely be a ZIP package. Whatever installation procedure you are using, it is straightforward; a serial number protects the product.

As said above, I installed the Embraer ERJ Family, which contains all the aircraft models, which means I end up in my X-Plane directory with one folder named “Embraer ERJ Family” that contains the ERJ135, 140, 145, 145XR and the Legacy 650. This newly released ERJ v2 package is for both X-Plane 11 and X-Plane 12.

After you have installed the ERJ package via the Aerosoft One Installer, you must enter the serial number of an X-Crafts model when selecting one of the models at X-Plane start-up. Afterwards, you can select any of the installed ERJ Embraer models without re-entering the serial number. After updating the model via the Skunkcrafts updater, you need to enter the serial number again.

Add-Ons
In addition to installing the aircraft models, you could install a couple of plugins. On purpose, I write “could” since it is not mandatory but handy.

First, the Skunkcrafts plugin. A quick note about the Skunkcrafts plugin: you also have a Standalone Client. The standalone client allows you to update the supported product without the need to start X-Plane. If you don’t use or want the Skunkcrafts updater, you need to re-download the latest version from Aerosoft.

Then the AviTab version 0.7.1. You can grab your copy via this dedicated X-Plane.Org link or directly via the AviTab GitHub page.

And last but not least, you need up-to-date AIRAC cycles for your navigation. Let me explain this in detail for those new to X-Plane. AIRAC (Aeronautical Information Regulation and Control) cycles are aeronautical information which is constantly changing: airspace structures and routes are revised, navigation aids change, SIDs (Standard Instrument Departure) and STARs (Standard Terminal Arrival Route) are amended, and runway and taxiway information changes.

Navigraph is the go-to source for everything you need for flight simulation. You must opt in for a Navigraph account. Once that’s done, you can select an Ultimate package on a monthly or yearly basis. You save 25% with the annual account compared to the monthly subscription.

Since SimBrief is an integral part of Navigraph, you can log in with the same credentials as your Navigraph subscription. But if you want to consider a Navigraph subscription, you can use SimBrief separately for free. The only thing you need to do is create a SimBrief account on the Navigraph website.

Updates
The Skuncrafts updater keeps all Embraer ERJs and E-Jets aircraft up to date. In the Embraer main aircraft folder, you will find the skunkcrafts_updater.cfg file and a skunkcrafts_updater_beta.cfg file. In the previous section, I already highlighted the need to install the Skunkcrafts plugin or how to do so by re-downloading the package.

Documentation, Settings and Liveries

The ERJ documentation can be found in the aircraft manuals folder. This folder offers the following Adobe Acrobat format documents:
– ERJ Family 2.0 by X-Crafts – FMS Manual
– ERJ Family 2.0 by X-Crafts – Expanded Checklist and Procedures Guide
– ERJ Family 2.0 by X-Crafts – Aircraft Manual

The FMS manual covers everything you need to know about the CDU. Further, it includes a flight plan description originating at EDDS (Stuttgart) and terminating at EDDF (Frankfurt).

The Expanded Checklist and Procedures Guide will be reviewed later, when I start the procedures. It is, in fact, the SOP (Standard Operating Procedure), though in a different format.

And last but not least, the Aircraft Manual; however, this is not yet complete. Or as X-Crafts says itself, “THIS MANUAL IS BEING WRITTEN. Hi! The systems manual is currently a work in progress. In the meantime, here are some great resources to get you started and so on.” Due to the absence of the aircraft manual, you will find links to YouTube movies and web documents on the second page; this is for the time being.

Unlike the E-Jets v2, there are no demo YouTube video flight tutorials, at least not yet, as of March 2026. The ERJ v2 does have an extensive description on how to follow their demo flight from Italy to Austria, but it is not yet available as a video, or it will probably never become available as a movie. A movie is great, I must agree with that, but a well written tutorial look alike document can be handy too.

There’s one note I need to bring to your attention: their newly introduced feature called AirComms. On this demo flight webpage, it is written about AirComms: “This entire Demo Flight can be guided by AirComms™, our intelligent in-sim guidance system. Go to the EFB AirComms tab, select the first tutorial and let AirComms give you clear instructions directly in the sim.” I will discuss that later in the review.

During my Part 2 ERJ Family review, I will perhaps utilise the X-Crafts demo flight for reference and describe in detail how helpful their demo flight web page is and how it differs from that of their E-Jets v2. As mentioned before, one major difference between the ERJ v2 and the E-Jets v2 is that the E-Jets demo flights are YouTube videos, whereas the ERJ demo flights are on a webpage.

Settings via X-Plane menu
The X-Crafts menu consists of “Please Select – X-Crafts Tech Support”, “X-Crafts Popup Panels” and the “EFB”. The first option opens your web browser and guides you to the Support X-Crafts page. You will find all kinds of suggestions on how to solve things, as well as using the Support page at X-Plane.Org.

The pop-up DUs option will be discussed later, while the EFB is right on in the next paragraph.

Then you have the X-Plane menu option EFB (Electronic Flight Bag), which, for clarity, refers to the X-Crafts EFB, not the AviTab EFB. This is double since the aircraft already comes with a built-in EFB mounted in each side window. The menu EFB offers a pop-up window of the EFB. This could be handy when you can move the popup EFB to a separate monitor or tablet. The pop-up EFB is sizable and offers several tabs:
– Ground Services
– Weight and Balance
– Takeoff perf(ormance)
– Landing perf(ormance)
– Checklists
– Settings
– AirComms
– AviTab

As you can see from the screenshots above, you can use either the built-in AviTab X-Crafts EFB or the floating pop-up window. The different EFB tabs speak for themselves, but don’t worry, some of them I will use during my test flight. I can remember that with the E-Jets models, there was a manual that explained all of that, but as of March 2026, there’s no such manual included with the ERJ models.

Liveries
My ERJ Family pack includes a couple of liveries, all of which are also available for the Legacy 650. But no worries. Many user liveries have been painted and can be found at the dedicated and organised by X-Craft team members X-Crafts ERJ Family X-Plane.Org website. On this X-Plane.Org link, you find general information, maintained by X-Crafts, about the liveries and a paintkit.

What I can see on the dedicated X-Crafts ERJ livery webpage, all liveries available on this page are, except for one, from real airliners. Nonetheless, it is amazing how many paintings have been done so far. According to a post from X-Crafts member Steve Wilson, “Note that all v1.0 liveries apply to v2.0 as well – no need to repaint! I’m using my moderator superpowers to move all existing ERJ 1.0 liveries to their new permanent home in the download manager. There’s a LOT of liveries to move, so Marko’s method is probably best, especially if you’re looking for something specific.”

The Real Embraer ERJ(S)

The Embraer ERJ family (ERJ = Embraer Regional Jet) is a regional jet designed and produced by the Brazilian aerospace company Embraer. The family includes the ERJ 135 (37 passengers), ERJ 140 (44 passengers), ERJ 145 (50 passengers), ERJ 145XR, and the Legacy 650 business jet.

Development of the ERJ 145 was launched in 1989. Its early design took the form of a turbofan-powered stretch of the existing turboprop-powered EMB 120 Brasilia regional aircraft. After the project was temporarily suspended in 1990, work on a revised configuration began in the early 1990s.

While retaining the three-abreast seating of the Brasilia, the twinjet features a new design and is powered by two rear-fuselage-mounted Rolls-Royce AE 3007 turbofans for a range up to 2,000 nautical miles. By the time of its maiden flight on 11 August 1995, Embraer had garnered 18 firm orders, 16 options and 127 letters of intent for the type. On 10 December 1996, the ERJ 145 received its type certificate; it entered revenue service with ExpressJet Airlines on 6 April 1997.

Design-wise, the airframe is composed of stretched, machined, and chemically milled aluminium, with CFRP for moving parts, GFRP for fairings and sidewalls, Kevlar for leading edges, and Nomex honeycomb-CFRP/GFRP sandwiches for floors.

The best and most reliable source for background information is, of course, the official Embraer website. And, of course, Wikipedia also offers a wealth of information, but I prefer to go to the official Embraer site.

Walk-Around Check

Introduction
Since I received the complete ERJ Family for my review, the question arises which model I shall use for my walk-around check. Or is there perhaps not much difference between these external models and their cockpits?

Let me first highlight this: the ERJ models, which share the same philosophy as the E-Jets, have approximately 95% parts-and-systems commonality across the four main ERJ types, reducing rotable inventories and maintenance costs. The cockpit has 99% commonality across the models, so they all require cross-crew qualification.

And finally, some words about the Legacy 650.
The Embraer Legacy 650 is a long-range business jet that can accommodate up to 13 passengers and features a spacious cabin divided into three zones. It has a range of approximately 3,900 nautical miles and is known for its large baggage capacity and comfortable amenities.

The Legacy 650 is known for its reliability and efficiency. It can operate nonstop flights on long routes, such as London to New York or Paris to Dubai. The aircraft’s design allows for quick turnarounds and easy maintenance, making it a popular choice for charter services. Overall, the Embraer Legacy 650 combines luxury, performance, and advanced technology, making it a strong contender in the business jet market.

The Legacy 650 builds upon the ERJ 145 platform but incorporates structural and systems upgrades. Embraer positioned it for transcontinental and select intercontinental routes. So it is easy for the flight crew to transition between the Embraer ERJ models. With this background, I decided to conduct a walk-around inspection of the ERJ-145.

My Inspection Impression
My very first impression of the ERJ-145, which is, to be honest, also applicable to all the other ERJ models, is ‘wow’. The level of detail is enormous. Let’s start as usual at the nose of the aircraft. One huge advantage is that the aircraft is relatively small, so you can inspect almost every part. Ok, you can’t reach the fuselage roof or tail from the ground, but it is much easier to inspect the ERJ model. When you compare that, for example, with an Airbus A330, A340 or 767, 777, 747-8i, you understand what I mean. I think you got the picture.

Anyway, you can clearly see the way the fuselage nose is modelled, the cockpit windows, and, of course, the NLG (Nose Landing Gear). The downside of such a smaller aircraft is that I need to go through my knees to see the NLG structure. The text or decals on the nose or near the NLG are unbelievably sharp. Despite that, panel latches are perfect, although that specific panel can’t be opened. Logically, otherwise it would require even more polygons for a panel to OPEN/CLOSE, and that cost affects FPS (Frames per Second), and I am not even talking about the interior of that area, which has to be modelled too.

The NLG has a so-called self-castering design, meaning the wheel’s centre lies behind the NLG strut. Nevertheless, a NWS (Nose Wheel Steering) system is needed. But OK, the NLG with wheels are well modelled, including all the decals that belong to it, and I even spot the tyre pressure fitting.

With the FWD PASS door opened, I have an excellent view of the modelled stair construction, the handrail, the steps, the latches in the door frame and the hinges. It is not of the same design as the E-Jets Lineage 1000 I had seen, but it is still well modelled.

I leave the FWD PASS door behind me, and via the fuselage, I walk towards the wing leading edge. I look up, and I am pleasantly surprised by how well and sharply the textures of this livery are rendered. Reaching the leading edge, I spot the MLG (Main Landing Gear), but leave that for later, since the MLG’s design is different from what we are used to. The wing-to-surface belly has several panels and lights, and although I don’t see screws or rivets on the individual panels, it still looks nice.

With this livery, United Express, I spot a couple of yellow painted objects on the front of the wing leading edge. Here they are yellow, but this is not always the case with other airliners. Time for some background on what these are and why they are so important.

“They are called vortilons. They can induce a vortex on the upper surface of the wing at high angles of attack, which allows flying at higher angles of attack before stalling. Additionally, four vortilons were installed on the lower surface leading edge of the outboard wing panel. Their interaction with the wing sidewash at high angles of attack produces strong vortices that are convected to the upper surface, where they modify the pressure distribution and boundary layer development, postponing flow separation and increasing maximum lift.”

“Their shape and position were defined using the 3D panel program. The combined effect of the leading-edge droop and vortilons enabled improved take-off and landing performance without resorting to more complex variable-geometry leading-edge devices (such as slats), at a small cruise performance penalty. Figure 22 shows a schematic representation of the ERJ145 droop and vortilon.” (Courtesy of Aviation.StackExchange.com

It is important because it is positioned on the wing leading edge, in front of the ailerons, which is essential for the aircraft’s roll characteristics. Just as a side note. The Douglas DC-9 had one of them mounted on the leading edge of its wings.

Following the leading edge to the wing tip, I see the awesome, highly realistic modelled NAV and STROBE light unit. Why awesomely and realistically ….. the plastic cover has several scratches on it. More than realistic is not possible. Further on, I see many static dischargers mounted on the aileron.

Via the wing trailing edge, I walk to the MLG, but before I reach the MLG, I use a virtual stair to check the top of the wing. It is clean, with some vortex devices mounted around the aileron area. Anyway, the MLG, wheel assembly and other components. It is all well modelled with many details. And now, it is a special landing gear construction, but first, has I nothing forgotten or is something wrongly modelled? No, in that respect, we know X-Crafts well about precise modelling and an eye for detail. That’s the same for this MLG with the wheels. First, the text or decals on the MLG strut. Even from a distance, I can read the information. I am referring to the service chart and the LIEBHERR manufacturer decal. Then, also important, lots of dirt, some weathered parts, but no scratches or whatsoever.

On purpose, I write no scratches since this is, according to the AMM (Aircraft Maintenance Manual), not allowed, or when there is a scratch, it must be noted, measured for length and depth. This is to prevent any corrosion that can appear over time. The MLG strut, shock absorber, torque links, wiring and hydraulic lines, and wheel brakes are all modelled with great precision. Hold on, I said that something is special about this landing gear, right?

Normally, you have the main landing gear strut, which also houses the main shock absorber. There is mostly one side strut with an overcenter linkage. In the case of the ERJ models, the shock absorber is separated from the main landing gear strut. Check out the first screenshot.

Up to the engines.
It is not easy to see the engine inlet from the ground, so I look at my virtual stair again to check the inlet, the fan blades, the sound-reduction material, the spinner cone, and other parts. The leading edge of the nose cowling is a beautifully shiny, glossy aluminium, while many polygons give it a nice, round shape. Wow, it is a shame you need to climb a virtual staircase to see how this is all done. Again, eye for detail! Since the engine cowling has lots of inspection panels, you will expect some decals for “what is what”, but I haven’t seen these decals, except one near the engine nose inlet.

At the rear of the engine, near the exhaust, I see the reversers, which were also on the 737-200 and DC-9/MD80 aircraft, the well-known bucket doors. This means that the fitted Rolls-Royce engines have no fan reversers but turbine reversers. And finally, a quick look at the rear of the engine. Again, you don’t see all the work, unless you use a virtual stair, which has been done to model a complete exhaust. Well done, I must say!

And finally, the tail of the ERJ.
The first thing at the tail is perhaps the APU (Auxiliary Power Unit) outlet. It seems to me that it should reflect a stainless steel outlet. Very nice to see, with all the screws to keep it all together. Then, on the vertical and horizontal stabilisers, I spot a lot of static dischargers, decals when visible and applicable, and even a visual marking for the stabiliser position. I noticed some dirt near the hinges and some wear, but just enough to make it look real. All the panels on the vertical fin are visible with a perfect 3D look, and that 3D look extends to the wings, fuselage, engine cowlings, and so on.

On the right-hand side, I walk back to the nose of the ERJ, but not before I open the door with my virtual stair and check the cabin interior. I am talking about the service door. You find the same as with all other doors: the necessary decals, sharp and readable, and all other parts that belong to the door are modelled, such as the door frame, door locks, handle, external door grip, etc. It is again a masterpiece, as we know from the E-Jets v2.

Overall, a beautifully modelled ERJ series.
Hold on, is the Legacy 650 worth performing a walk-around check too? No, not really. The Legacy 650 is based on the ERJ-145; it doesn’t have a service door, and the rest are the same as on the ERJ-145.

Ground equipment, virtual cabin, and cockpit

As with the ERJ aircraft, all X-Craft models come with internal and external animations and/or ground equipment. Let’s start with the ground equipment and animated objects.

The ground equipment objects, for all models, are the GPU (Ground Power Unit), Ground Objects (safety cones and wheel shocks), and the Engine Covers (engine inlet covers and and REMOVE BEFORE FLIGHT red flags).
The animated objects depend on the aircraft type, specifically on whether it is the Legacy 650 or another ERJ model. Regarding the external animations, the ERJ 135/140/145/145XR models all have an animated FWD entrance door with built-in stairs, and an animated AFT CARGO and FWD SERVICE door with a door handle. The Legacy 650 is slightly different since it has no FWD SERVICE door. All other animations are the same.

If you are looking for an animated pushback truck or pushback function, you won’t find it. Instead, I recommend using the BetterPushback plugin. If you’re looking for an awesome pushback truck that delivers an “as real as it gets” experience, consider the Better Pushback plugin. It is easy to control and works flawlessly with X-Plane 12. If you don’t want or need this add-on plugin, you can always use the built-in Laminar Research X-Plane pushback function. It is basic and lacks animation.

Virtual Cabins ERJ 135/140/145/145XR
I am always wondering how the virtual cabin is modelled. Some simmers find it an absolute necessity, while others are more interested in the well-modelled cockpit and how aircraft systems are simulated.

Anyway, let’s first explore the ERJ 135/140/145/145XR.
Via the FWD entrance door, I spot the CABIN LIGHTS panel on my right-hand side after entering the FWD galley or pantry. The panel is used not only to control the cabin lights but also to control temperature, emergency lights, attendant calls, the PSU (Passenger Service Unit), and door CLOSURE. Not all of what you see is modelled. Only the CEILING and SIDEWALL lights work; you can control them ON/OFF and adjust their brightness. With the DOOR switch, you can OPEN and CLOSE the entrance door.

The virtual cabin is nicely modelled; the seats with their belts look real, and the sidewall and ceiling panels are well modelled, and I should not forget the EXIT signs. The same as, although small, the pantry with carts, latches and so on. The lavatory doors at the back of the cabin are not animated; the window blinds are not animated either. Hold on, the cockpit door looks realistic, and logically, it is animated, but this will be different as we explore the Legacy 650 virtual cabin.

The passenger or VIP entrance door from the Legacy 650 is basically the same as with the other models, though the cockpit door is different. Yes, it is animated, but it is made of a mahogany wood structure. Via the same well-modelled, integrated FWD stair, I see a similar cabin control panel on my right-hand side; however, this one is not powered. When I switch on the cockpit electrical power, the panel comes to life. And again, I can control the galley and cabin ceiling/wall lights. This differs not from the 135/140/145/145XR, although the panel simulates a state-of-the-art look and feel.

And yes, of course, the FWD pantry/galley is different. It is actually a business model, so all cuberts are covered with the same wooden structure as the cockpit door, though no animations are available here. The same for the FWD lavatory, but you can control the sliding doors to the VIP cabin.
The virtual VIP cabin is well-made, as I’ve seen already with the E-Jets Lineage 1000. Also, the Legacy 650 has lots of animations. There’s so much to see: relaxing chairs, beautifully modelled cabinets, a nice virtual carpet, and sleek ceiling panels. Since it is a business layout, there are no overhead bins in this model. To wrap it up, the cabin is awesomely modelled with an eye for many details.

Hold on, there is more. Animated monitors in the back; a click on the display triggers the appearance of the AviTab. X-Crafts has implemented pre-departure information, which can be personalised. After the FMS is programmed, the tablet displays flight information, and you can also switch to Avitab individually to display maps.

I must conclude that a great deal of time and effort goes into creating such a virtual cabin. As I mentioned before, the FWD toilet isn’t animated, and the AFT lavatory isn’t either. All the tables in the cabin are foldable, and individual lighting can be switched OFF and positioned to your wish. But there’s more. Window blinds can also be controlled smoothly via the galley/pantry control panel.

Cockpit
With this wow effect, it is time to check out the ERJ cockpit. As you have noticed, I don’t use the term “flight deck” because Embraer doesn’t either in their official papers. They refer to the cockpit.

I entered the cockpit via the open cockpit door. If it is closed, simply click the door lock in the cabin entrance, and the door opens. And yes, I had the same feeling when I entered the cabin; I am happy with what I see. The cockpit layout is basically the same for the Legacy 650 and the other models except that the Legacy has a creme carpet and all looks clean and hardly worn out or weathered while the other “airliner” models have a lot of weathering on the seat construction as well as, a grey painted floor with lots of spots with missing paint, as it is expected in real. This missing paint simulates weathering in an airliner’s cockpit.

It seems to me, though many other configurations are possible, that the pilot seats are covered in imitation leather, and some fabric is used for the backrests and seats. It looks awesome, to be honest, although I am aware it is only a seat.

When I look left and right from the entrance position, I can see a protective breathing-equipment box behind each pilot seat. That’s all. In that way, it is a clean cockpit. The only animation I found on the pilot seats is in the armrests, which operate simultaneously on either seat when you click one.

Moving from the Captain’s side panel to the main instrument panel, I have a good view of the DUs (Display Units). The typical Embraer control wheel is well modelled and heavily weathered. When you have the time to check it out, I checked the control column floor fittings and how they are made. Awesome. So realistic.

Although there is not much weathering on the sub-panels, all the tiny buttons and switches are included. Nice to see how realistic it looks. And then the pedestal. This looks clean, slightly weathered, but not too much. I am impressed by everything, and this impression is confirmed when I zoom in on the main instrument panel and centre section. Everything is so sharp, razor sharp, I should say. No blurry text near each switch or knob, no blurry on the DUs, and the perfect readability of all other instruments. I didn’t mention this, but when you zoom in on a panel, the text is definitely weathered. Perfect!

And finally, the overhead panel with the circuit breaker section above it. The panel shows clear weathering and spots from frequent use of selectors, buttons, or switches, while the overall text is sharp and beautifully lit from the back, though clearly not “new” anymore. And that is good news. The overall weathering is nicely done. Not too much, not too little.

And are there any animated objects?
As mentioned earlier, the cockpit door and the Captain and Co-pilot armrests on each seat are animated simultaneously when clicked. The EFB can be moved in any direction or made to disappear. And think about this, the sliding windows are animated too, ok, that’s good news, but when you move the sliding window by clicking the knob, the EFB has to be moved as well with the sliding window. Adding to the sliding windows: when you click the button, the window opens, but it doesn’t slide back because there’s no space to do so. So, actually, it is not a sliding window but just opening the window. Anyway, well modelled!

Then some words about the 2D pop-up displays.
All the ERJ models have the same pop-up DUs as its bigger brother, the E-Jets. They are equipped with several 2D pop-up panels/displays. The popups are for the PFD (Primary Flight Display), MFD (Multi-Function Display), EICAS (Engine Indication and Crew Alerting System), and the FMS CDUs (Flight Management System Control Display Units). You can see them either by clicking the respective cockpit display/CDU or via the X-Crafts X-Plane menu X-Crafts ERJ xxxx – X-Crafts Popup Panels. The xxx identifies which model is active.

Once you have a pop-up DU or panel, let’s assume you have chosen the MFD. In the left-hand upper corner, you can lock its position on the computer X-Plane monitor, or you can make it a floating panel.

To cancel the pop-up, you click the “X” located in the right-hand upper corner or click the DU in the instrument panel. And, you can resize them. Place your mouse “somewhere” on the pop-up DU, and use the scroll wheel to increase or decrease the panel size. When you have a macOS Magic Mouse, you slide your finger over the middle section of the mouse.

A Powered Cockpit

Following the previous section on how the 3D cockpit is modelled, it is now time to check out when it is electrically powered. Curious to see how the systems work and what the different EFIS and EICAS displays look like?

It is also worth checking out which switches are operational, as far as possible. In my upcoming Part 2 X-Crafts ERJ v2 review, which will cover at least one test flight, I’ll provide you with much more in-depth information. I can, via the EFB, connect the GPU (Ground Power Unit) to the aircraft, or I can start the APU (Auxiliary Power Unit). I do both tests and see how it powers up. It allows me to test how the aircraft systems work together. And I will use the implemented X-Crafts AirComms for these simple tests.

Anyway, let’s see how the systems look when I apply electrical power to the aircraft, how realistic the display images are, how well the integral lighting works, whether a switch or knob does what it’s supposed to, and so on.

I use, for instance, the integrated awesome feature AirComms to power up the aircraft and, more importantly, to check how it works. I will discuss AirComms in more detail in a later section. There is one other “thing” I find illogical when using AirComms: the FMS CDU is not even programmed while the engines are already started. Time to contact X-Crafts and ask them why they did it this way. According to X-Crafts, “It is aimed to be suitable also for total beginners, which is why I start with a power-up and engine startup. You can, however, follow the expanded procedures document in the manuals folder for realistic procedures.”

My feelings tell me that, whether beginners or not, everybody should learn to program the FMS CDU before the engines are started, so learn it the right way: program the FMS CDU before starting the engines. Real pilots do it the same way, too!

Then I restart the entire procedure using the ERJ Family 2.0 by X-Crafts – Expanded Checklist and Procedures Guide document. Or you can also follow the steps using the demo flight on the X-Crafts website, but keep in mind that the engines are also started first, and afterwards the FMS CDU is programmed. And then there is, of course, the XChecklist with the clist option, but that’s for later.

Aside from a couple of non-functional switches, around roughly 95% of the switches and selectors related to the aircraft systems are simulated. Knowing this, I am impressed by the presentation of images on the various DUs – as real as it gets – and other instruments, such as the IESS (Integrated Electronic Standby System), as well as the integral lighting of all the sub-panels.

And although it may be normal with X-Crafts models to have 2D pop-up DUs, it is not as common as you think. I can conclude that the 2D popups, such as those of the PFD, MFD and EICAS DU, are of superior quality. Besides that, you can resize the DU with your mouse wheel. And frame rates impact … I hardly noticed that on my Apple MBP with M4 Max Silicon.

And what happens at sunset or sunrise with the cockpit’s integral lighting? Not many words are needed to see how beautiful this illuminated cockpit looks. It is just awesome. It is just wow.

Implemented Auto Flight Systems

During one of my conversations with Marko from X-Crafts, we discussed the depth to which systems are programmed, with a particular focus on the Auto Flight systems. Marko informed me that, “Our ERJ models have an authentic FMS and autopilot with all modes implemented. More precisely, we implemented individual AP sources for Captain and F/O. Further on, a realistic simulation of the electrical, fuel, APU, hydraulic, anti-ice, and pneumatic systems, including all system tests that real pilots need to perform during standard operations.

 

Add to this a realistic Thrust Rating System for derating the engines in different flight phases and accurate EICAS warning, caution, and advisory logic. Good to know, the flight model was developed and fine-tuned by X-Aerodynamics, the industry leader for simulating precise aerodynamics and the right feel.”

This means that the X-Crafts ERJ v2 aircraft has reached the upper limits of realistic behaviour, which is awesome news. As Marko already said, the FMS CDUs are implemented separately, as are the EFIS displays. You can select different images or functions on the Captains and F/O MFD. This is also applicable to the PFDs. Check out the following screenshots.

AviTab Support

The X-Crafts ERJ v2 has full integration with AviTab (Aviation Tablet). When I write “full”, I mean not only the AviTab device with its basic functions, but also SimBrief integration, TO and LDG data tabs, the Weight and Balance tab, and a direct, bidirectional link to the X-Crafts EFB (Electronic Flight Bag).

Hold on, not too fast.
The AviTab EFB plugin is something different from the X-Crafts EFB. Ok, they use the same name …. EFB, but the X-Crafts EFB is by default an individual pop-up. You can integrate this X-Crafts EFB pop-up window into the AviTab EFB. Then it looks a bit more realistic, and all X-Crafts EFB functions remain available. And, when needed, you can always have the individual X-Crafts EFB as a pop-up window, which is handy since you don’t always want to look at the side window.

Wrapping it up, the X-Crafts ERJ EFB is positioned on each side window. Very convenient for you as a virtual pilot, especially when using VR. As briefly mentioned before, the X-Crafts EFB has the option to link your SimBrief/Navigraph account to the tablet. This allows you to download, for example, flight plans directly into the FMS CDU. And the AviTab lets you store charts and other documents in its designated folder.

It will then be all available via the AviTab for your cockpit preparations. Real ERJs also have such a tablet near each pilot. Not exactly in the same position, but it is common for real ERJ pilots to have such a device available to them.

Using Checklists or AirComms

X-Crafts EFB Checklist
First, the X-Crafts ERJ EFB has a checklist tab. Although it does offer detailed steps to follow, it is not linked to any ERJ aircraft system. This means it is just a static checklist. When you switch on a system or select a knob, nothing happens in the checklist. For example, when you select the battery knob to AUTO, there’s no feedback on this X-Crafts EFB checklist. This kind of checklist behaviour is the same as I know from the E-Jets v2.

Acrobat Expanded Checklist and Procedures Guide
If you prefer a different way to prepare, you can use the included Adobe Acrobat “Expanded Checklist and Procedures Guide” document in the X-Crafts Embraer ERJ Family manuals folder. You can print this document and use it. It is not just a document based on nothing; no, it is based on the real SOP (Standard Operating Procedures) and related checklists without the Embraer headers at the top. And that brings me automatically to: with the release of the ERJ v2, a new feature has been added: the AirComms tutorials, or should I call it the interactive checklist? Let’s check that out, right?

X-Crafts New Feature “AirComms”
AirComms can be found in the X-Crafts EFB. It is an interactive, self-explanatory checklist guide for a flight from LIME (Milan Bergamo Airport) to LOWW. (Vienna Airport) Everything necessary to prepare your flight, including the use of the SOP and related checklists, is covered. Although I took some screenshots, they are only a fraction of how it works and looks. AirComms sometimes expects you to have familiarised yourself with the aircraft systems and where to find switches and knob. That said, sometimes you need to know where a switch or knob is located. When you familiarise yourself with how the systems work and where they are located, you can continue with the next AirComms steps.

As mentioned before, you immediately notice that you are dealing with a demo flight tutorial. When you own the X-Crafts E-Jets v2 and follow Marko’s YouTube videos, you know now that with AirComms in the ERJ v2, you have Marko with you all the time, over and over.

You can select, using the top dropdown, which tutorial section to start with. The font size of the AirComms pop-up can be adjusted to your preference, as well as where you want to have the AirComms pop-up. If you selected a font that’s too small, you can change the font size on-the-fly.

XChecklist with clist
In case you prefer the famous XChecklist (https://forums.x-plane.org/files/file/20785-xchecklist-linwinmac/), I have good news. There is an updated clist for the ERJ v2. It is created by X-Plane.Org user jengle. His checklist can be downloaded via this link (https://forums.x-plane.org/files/file/98331-clist-for-xchecklist-xcrafts-erj-family-version-2/), and he also created a YouTube video that covers a complete flight using the updated checklist file. According to Jeff Engle, “This is the updated checklist for the XCrafts ERJ Version 2 series. This example uses the ERJ 145 and is an expanded checklist covering GPU and APU connected startups.”

Flight Management System and Flight Plans

FMS CDU or MCDU
The X-Crafts ERJ and the E-Jets also work with the X-Plane flight plan extension “fms”. You have two options to create FMS flight plans: either use an offline or online program, or enter all the waypoints step-by-step in the FMS CDU or sometimes the X-Crafts manual calls it MCDU.

A bit confusing to be honest, since a CDU is different from an MCDU. As you might know, the “M” stands for Multipurpose or Multifunction, whereas the CDU has no additional functions and is confusing, since the official Honeywell FMZ manual discusses the CDU. Time to contact X-Crafts and see what they can say about this. According to X-Crafts, “The official Honeywell FMZ name is CDU, but even Embraer uses MCDU in their own manuals.”

As just mentioned, if you prefer not to use a flight plan program, you can create a flight plan directly in the FMS CDU or, if you prefer, the MCDU. I will explain that later; however, it is normal that pilots select a company route from the CDU. For pilots, there is no need to enter all waypoints into the CDU. This is done by uploading the flight plan, either from the stored flight plan in the designated X-Plane folder (Output/FMS plans) or via a direct upload link from SimBrief, whichever applies. The only actions they need to add to the flight plan are the SID (Standard Instrument Departure), the STAR (Standard Terminal Arrival Route), and, if applicable, any necessary changes.

Flight Plan Sources – Navigraph
Well-known and fully integrated with AviTab is Navigraph/simBrief. When you want to use SimBrief without updated Navigraph AIRAC cycles, you first need to create a free SimBrief account to get access. This account is made via the Navigraph website. After you have created a free Navigraph account, you can use the same account for SimBrief. I would suggest that, if you don’t have it done yet, you go for a Navigraph subscription.

This subscription provides access to AIRAC cycles, but Navigraph offers much more than that. For AIRAC cycles and related services, you need a payware account with Navigraph. And yes, it costs roughly 100 euros, but it is worth every euro or whatever currency you are using to pay with.

Flight Plan Sources – Little NavMap
Another interesting offline planning tool is the freeware program LittleNavMap. The program is compatible with Windows, macOS, and 64-bit Linux. Although LittleNavMap offers much more than just flight planning, it still requires up-to-date AIRAC cycles, so a Navigraph account is a must. Something else to keep in mind is that the AIRAC cycle of the created flight plan must match the AIRAC cycle you use in X-Plane, or you get a mismatch warning.

Then, it’s essential to have updated and up-to-date performance files. That said, don’t forget to download the X-Crafts ERJ Family performance files from the Little NavMap website. All those ERJ files are from February 2025, so I am not sure if they are correct for the ERJ version 2.x. The same applies to SimBrief Performance Tools, although no date is indicated for when the performance files will be available.

Your Flight Plan
Those simmers who don’t prefer to use the “ready to load” flight plan described in the previous paragraph can enter the waypoints by themselves in the FMS CDU. When you want to enter your flight plan manually into the CDU, check out the X-Crafts FMS document, which starts immediately with how to enter waypoints. And when you use the X-Crafts LIME-LOWW demo flight steps, you will also enter them manually in the FMS CDU.

Note: keep in mind that the X-Crafts FMS manual explains a flight from EDDS (Stuttgart) and terminates at EDDF (Frankfurt) while the AirComms tutorial discusses a flight from LIME (Milan Bergamo Airport) to LOWW (Vienna International Airport).

Which Hardware to Use?

When using a joystick, you can use any joystick, and when it comes to throttle control, you can use any device for this. I used the Thrustmaster TCA Airbus side-stick, but you can also use, for example, the Saitek X-52. If you own a control wheel device, such as the Honeycomb Alpha Flight Controls paired with the Honeycomb Bravo Throttle Quadrant, it will also work perfectly with the X-Craft aircraft. Neither the X-Crafts ERJ document advises you on which hardware would be best for their ERJ aircraft.

I am aware that I only highlighted a couple of hardware brands, but there are, of course, many others on the market, such as Thrustmaster, Logitech, Turtle Beach, and CH. When you are thinking of buying new hardware for the X-Crafts ERJ Family, then it’s perhaps a good idea to check out our in-depth hardware reviews page. Funny to end with is that I have never seen hardware that reflects the typical Embraer controls.

What said, I decided to try out my Thrustmaster TCA Airbus set with the X-Crafts ERJ Family. I am aware that the hardware is dedicated to twin-engine Airbus aircraft, but it should also work with Embraer X-Craft models. Assigning the major channels isn’t a problem. Assigning switches or selectors works as well, but one example causes some issues: the FLAPS.

The available FLAP gate positions on the Thrustmaster FLAP lever differ from those on Embraer models. It’s not a big deal; you need to be a bit flexible. I also found that the precise throttle assignment is not easy. Assigning the throttles on the TCA Throttle Quadrant to X-Plane is straightforward, but fine-tuning is complicated because the X-Crafts EFB doesn’t have the option to fine-tune throttles and reverser “points” as is, for example, possible with ToLiss. Anyway, I didn’t run into any problems using this hardware versus any X-Crafts ERJ model.

Summary Part 1

I always try to keep the review as short as possible while still including all the necessary information, but I can’t. When I become enthusiastic about a product, I am in, and I continue, and so on. This has decided me to, again, split the X-Crafts ERJ Family into Part 1 and Part 2 reviews. Also worth noting that this review is based on product version 2.1.0-rc2.

Having completed Part 1 of the X-Crafts ERJ Family review, I am impressed by the model’s 3D representation, both exterior and interior. And let’s not forget their implemented AirComms. Ok, the AirComms may be based on a typical flight from LIME to LOWW, but it can be used for any other flight you make. The only difference is the FMS CDU part. Personally, I would love to see that the right procedure was followed with the AirComms, meaning the FMS programming was completed before the engines were started. With such a well-modelled ERJ series, it would add another level of realism.

As of this writing, March 30th, 2026, this review covers the X-Crafts ERJ Family version 2.1.0-rc2. For this review and the screenshots I made, I used the following add-on software:

– Payware | X-Plane 12.4.0-r2 (logically)
– Payware | Navigraph AIRAC Cycles and Charts
– Payware | World Traffic 3
– Payware | Taimodels Orlando-Sanford (KSFB)
– Freeware | AviTab
– Freeware | OpenSceneryX
– Freeware | XChecklist v1.52
– Freeware | clist.txt from Org user jengle
– Freeware | FlyWithLua NG v2.8.12 for X-Plane 12
– Freeware | SkunkCrafts Updater v12.1r2 for X-Plane 12
– Freeware | BetterPushback 1.12
– Freeware | WalkAround for xplane

Apart from the add-ons listed in Part 1 of this review, I hope you find the contents useful. I tried to cover different aspects, not always directly related to the X-Crafts Embraer package, but also provide additional helpful information, and overall, the X-Crafts ERJ v2 Family. Did I cover everything so far? I hope I covered most of the ERJ models, but I’m sure I have forgotten something. If I did, I could hopefully highlight it in the upcoming Part 2.

And now, heading for Part 2. As just said, it will cover a complete “tutorial” flight using the X-Crafts demo as a guideline, as well as the FMS tutorial. As with many other Part 2 aircraft reviews I have done before, I intend to cover a full flight, divided by flight phase, as well as all other preparations and experiences related to the X-Crafts Embraer aircraft model.

See you soon!

Feel free to contact me if you’ve got additional questions related to this impression. You can reach me via email Angelique.van.Campen@gmail.com or to Angelique@X-Plained.com.

With Greetings,
Angelique van Campen

 

 

Add-on:Payware Part 1 - X-Crafts Embraer ERJ v2 Family
Publisher | Developer:Aerosoft / X-Plane.Org | X-Crafts
Description:Ultra realistic rendition of the Embraer ERJ 135 / 140 / 145 / 145XR / Legacy 650
Software Source / Size:Download / Approximately 4.9 Gb (zipped)
Reviewed by:Angelique van Campen
Published:March 31st 2026
Hardware:- MacBook Pro M4 Max 14" / 64Gb RAM / 1TB
- Intel 3GHz Intel Xeon W / 4.5Ghz
- Thrustmaster TCA Captain Pack Airbus Edition
Software:- macOS Tahoe 26.3.1
- X-Plane 12.4.0

0 Comments

Submit a Comment

This site uses Akismet to reduce spam. Learn how your comment data is processed.